Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Parti

Nessuna parte specificata.

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Before you begin, make sure the 700m is powered off.
    • Before you begin, make sure the 700m is powered off.

    • Unplug the power cable.

    • Flip the 700m over and remove the battery.

    • Slide the battery release switch toward the center of the 700m, and then pull the battery free from the back.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the two Phillips screws securing the RAM cover.
    • Remove the two Phillips screws securing the RAM cover.

    • Remove the RAM cover and set it aside.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Two clips secure the RAM module in place, one on each side. Using your fingers, spread the clips away from the RAM module. When released, the RAM module will pop up at a slight angle. Lift the RAM module to an angle of about 30 degrees and slide it out.
    • Two clips secure the RAM module in place, one on each side. Using your fingers, spread the clips away from the RAM module.

    • When released, the RAM module will pop up at a slight angle.

    • Lift the RAM module to an angle of about 30 degrees and slide it out.

    • When handling the RAM module, touch only the outside edges. Take care not to touch the gold-colored contact points along the bottom edge.

    • To install a new RAM module, slide it in place at about the same angle until it is snug, and then swing it downward until the two clips snap into place.

  4. APRI TUTTE LE SCHEDE

    Kit espansione RAM per Mac

    Acquista Kit

    Abbastanza RAM
    Per tutte le schede

    Acquista Kit
  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the 700m over and swing the screen all the way open until it lays flat. Beginning from the left side, use the flat end of a spudger to gently pry up the plastic trim that runs along the top edge of the keyboard. Remove the trim. Beginning from the left side, use the flat end of a spudger to gently pry up the plastic trim that runs along the top edge of the keyboard. Remove the trim.
    • Flip the 700m over and swing the screen all the way open until it lays flat.

    • Beginning from the left side, use the flat end of a spudger to gently pry up the plastic trim that runs along the top edge of the keyboard. Remove the trim.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the two Phillips screws securing the keyboard.
    • Remove the two Phillips screws securing the keyboard.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Tilt the top of the keyboard up at an angle, and gently push the keyboard toward the back of the 700m, freeing the tabs along the bottom.
    • Tilt the top of the keyboard up at an angle, and gently push the keyboard toward the back of the 700m, freeing the tabs along the bottom.

    • Do not push very hard, or you may damage the keyboard ribbon cable.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Tilt the bottom of the keyboard up at an angle. Use the pointed end of a spudger to disconnect the keyboard ribbon cable by pushing open the clips on either side. Remove the keyboard and set it aside.
    • Tilt the bottom of the keyboard up at an angle.

    • Use the pointed end of a spudger to disconnect the keyboard ribbon cable by pushing open the clips on either side.

    • Remove the keyboard and set it aside.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the two Phillips screws securing the inner RAM cover. Tilt the right side of the RAM cover up at an angle and pull it free.
    • Remove the two Phillips screws securing the inner RAM cover.

    • Tilt the right side of the RAM cover up at an angle and pull it free.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Two clips secure the RAM module in place, one on each side. Using your fingers, spread the clips away from the RAM module. When released, the RAM module will pop up at a slight angle.
    • Two clips secure the RAM module in place, one on each side. Using your fingers, spread the clips away from the RAM module.

    • When released, the RAM module will pop up at a slight angle.

    • Lift the RAM module to an angle of about 30 degrees and slide it out.

    • When handling the RAM module, touch only the outside edges. Take care not to touch the gold-colored contact points along the bottom edge.

    • To install a new RAM module, slide it in place at about the same angle until it is snug, and then swing it downward until the two clips snap into place.

Linea Traguardo

Altre 4 persone hanno completato questa guida.

Jeff Suovanen

Membro da: 06/08/2013

307.729 Reputazione

255 Guide realizzate

Team

iFixit Membro di iFixit

Community

129 Membri

12.528 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 15

Tutti i Tempi: 2,999