Introduzione

In this guide, we will be showing you how to remove and replace the Display Assembly.

Parti

Nessuna parte richiesta.

  1. WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  2. Peel off the camera cable from the computer base.
    • Peel off the camera cable from the computer base.

  3. Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.
    • Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.

  4. Remove the screw (M3x3) that secures the display-cable bracket to the system board.
    • Remove the screw (M3x3) that secures the display-cable bracket to the system board.

  5. Lift the display-cable bracket off the computer base.
    • Lift the display-cable bracket off the computer base.

  6. Using the pull tab, disconnect the display cable from the system board.
    • Using the pull tab, disconnect the display cable from the system board.

  7. Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.
    • Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.

  8. Remove the two screws (M2x3) that secure the display assembly to the computer base.
    • Remove the two screws (M2x3) that secure the display assembly to the computer base.

  9. Remove the two screws (M2.5x5) that secure the display assembly to the computer base.
    • Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

  10. Spedizione gratuita per tutti gli ordini superiori a 100 US$ o contenenti un Kit Attrezzi Pro Tech!

    Sfoglia il Nostro Negozio
  11. Turn the computer over and open the display.
    • Turn the computer over and open the display.

  12. Remove the two screws (M2.5x5) that secure the display assembly to the computer base.
    • Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

  13. Lift the display assembly off the computer base.
    • Lift the display assembly off the computer base.

  14. Align the screw holes on the NEW display assembly with the screw holes on the computer base.
    • Align the screw holes on the NEW display assembly with the screw holes on the computer base.

  15. Replace the two screws (M2x2.5) that secure the display assembly to the computer base.
    • Replace the two screws (M2x2.5) that secure the display assembly to the computer base.

  16. Close the display and turn the computer over.
    • Close the display and turn the computer over.

  17. Replace the two screws (M2x3) that secure the display assembly to the computer base.
    • Replace the two screws (M2x3) that secure the display assembly to the computer base.

  18. Replace the two screws (M2.5x5) that secure the display assembly to the computer base.
    • Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

  19. Route the display cable through the routing guides on the computer base.
    • Route the display cable through the routing guides on the computer base.

  20. Adhere the display cable and the camera cable to the computer base.
    • Adhere the display cable and the camera cable to the computer base.

  21. Connect the display cable to the system board.
    • Connect the display cable to the system board.

  22. Align the screw hole on display-cable bracket with the screw hole on the computer base.
    • Align the screw hole on display-cable bracket with the screw hole on the computer base.

  23. Replace the screw (M3x3) that secures the display-cable bracket to the computer base.
    • Replace the screw (M3x3) that secures the display-cable bracket to the computer base.

  24. Route the antenna cables through the routing guides on the computer base.
    • Route the antenna cables through the routing guides on the computer base.

  25. Adhere the camera cable to the computer base.
    • Adhere the camera cable to the computer base.

  26. Connect the camera cable to the system board.
    • Connect the camera cable to the system board.

Linea Traguardo

Un'altra persona ha completato questa guida.

Terrence15

Membro da: 18/12/2017

70.653 Reputazione

442 Guide realizzate

Team

Informative Technologies Inc. Membro di Informative Technologies Inc.

Community

15 Membri

925 Guide realizzate

i bought the version with the tn panel, is there a list of compatible ips panels for this particular model? thanks

michael gunawan - Replica

Hello, I bought an IPS version around a year ago but in that time a number of things happened, The computer goes to sleep without the lid being down, so i changed the setting to “Do nothing” when i closed the lid. As you expect it did not help, insead of going to sleep the display goes black, Also my ASDFJKL keys dont work, they work somethimes but im typing on a wired keyboard because of it. I NEED HELP PLEASE HELP

Dereck Scott - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 20

Ultimi 30 Giorni: 81

Tutti i Tempi: 693