Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Close the display and turn the computer over.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Loosen the captive screws that secure the base panel to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a plastic scribe, gently release the tabs that secure the base panel to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the battery cable from the battery-cable connector.
-
Turn the computer over.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Press and hold the power button for 5 seconds to ground the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Connect the battery cable to the battery-cable connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Align the tabs on the base panel with the slots on the computer base and snap the base panel into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Tighten the captive screws that secure the base panel to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the screws that secure the solid-state drive bracket to the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the pull tab, pivot the solid-state drive bracket and peel off the bracket from the tabs on the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the pull tab, disconnect the solid-state drive cable from the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the screws that secure the solid-state drive assembly to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the solid-state drive assembly off the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the screw that secures the solid-state drive to the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide and lift the solid-state drive off the solid-state drive assembly.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the NEW solid-state drive into the slot on the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the screw that secures the solid-state drive to the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Align the screw holes on the solid-state drive assembly with the screw holes on the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the screws that secure the solid-state drive assembly to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Connect the solid-state drive cable to the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Align the screw holes on the solid-state drive bracket with the screw holes on the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the screws that secure the solid-state drive bracket to the solid-state drive assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the latches and disconnect the keyboard and keyboard-backlight cables from the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the screws that secure the palm-rest assembly to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the computer base slightly and push the release tabs on the palm-rest assembly until it pops out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over and open the display as far as possible.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a plastic scribe, pry up along the edges of the palm-rest assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the palm-rest assembly and turn it over.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the connector latch and disconnect the power-button board cable from the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the palm-rest assembly off the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the keyboard.
-
Remove the power-button board.
-
Remove the status-light board.
-
Remove the Touchpad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the touchpad.
-
Replace the status-light board.
-
Replace the power-button board.
-
Replace the keyboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Connect the power-button board cable to the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Align the palm-rest assembly on the computer base and snap it into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Close the display and turn the computer over.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the screws that secure the palm-rest assembly to the computer base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Connect the keyboard cable and the keyboard-backlight cable to the system board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer
-
Lift the connector latch and disconnect the touchpad cable from the touchpad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the screws that secure the touchpad to the palm-rest assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the touchpad off the palm-rest assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Align the screw holes on the touchpad with the screw holes on the palm-rest assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Replace the screws that secure the touchpad to the palm-rest assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the touchpad cable into the touchpad connector and press down the latch to secure the cable.
-