Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 1
    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer After working inside your computer, follow the instructions in After Working Inside Your Computer For more safety best practices, see the regulatory compliance home page.

    • Close the display and turn the computer over.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 1
    • Loosen the captive screws that secure the base panel to the computer base.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • Using a plastic scribe, gently release the tabs that secure the base panel to the computer base.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Disconnect the battery cable from the battery-cable connector.

    • Turn the computer over.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 1
    • Press and hold the power button for 5 seconds to ground the system board.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Connect the battery cable to the battery-cable connector.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Align the tabs on the base panel with the slots on the computer base and snap the base panel into place.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 1
    • Tighten the captive screws that secure the base panel to the computer base.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

    • Remove the screws that secure the solid-state drive bracket to the solid-state drive assembly.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 2 : passo 10, immagine 2 di 2
    • Using the pull tab, pivot the solid-state drive bracket and peel off the bracket from the tabs on the computer base.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Using the pull tab, disconnect the solid-state drive cable from the system board.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 2 : passo 12, immagine 2 di 2
    • Remove the screws that secure the solid-state drive assembly to the computer base.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 1
    • Lift the solid-state drive assembly off the computer base.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 1
    • Remove the screw that secures the solid-state drive to the solid-state drive assembly.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 2 : passo 15, immagine 2 di 2
    • Slide and lift the solid-state drive off the solid-state drive assembly.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 1
    • Slide the NEW solid-state drive into the slot on the solid-state drive assembly.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 2 : passo 17, immagine 2 di 2
    • Replace the screw that secures the solid-state drive to the solid-state drive assembly.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 2 : passo 18, immagine 2 di 2
    • Align the screw holes on the solid-state drive assembly with the screw holes on the computer base.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 19, immagine 1 di 1
    • Replace the screws that secure the solid-state drive assembly to the computer base.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 20, immagine 1 di 1
    • Connect the solid-state drive cable to the system board.

  21. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 21, immagine 1 di 1
    • Align the screw holes on the solid-state drive bracket with the screw holes on the solid-state drive assembly.

  22. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 22, immagine 1 di 2 : passo 22, immagine 2 di 2
    • Replace the screws that secure the solid-state drive bracket to the solid-state drive assembly.

  23. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 23, immagine 1 di 1
    • Lift the latches and disconnect the keyboard and keyboard-backlight cables from the system board.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 24, immagine 1 di 1
    • Remove the screws that secure the palm-rest assembly to the computer base.

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 25, immagine 1 di 1
    • Lift the computer base slightly and push the release tabs on the palm-rest assembly until it pops out.

  26. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Turn the computer over and open the display as far as possible.

  27. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 27, immagine 1 di 1
    • Using a plastic scribe, pry up along the edges of the palm-rest assembly.

  28. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 28, immagine 1 di 1
    • Gently lift the palm-rest assembly and turn it over.

  29. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 29, immagine 1 di 2 : passo 29, immagine 2 di 2
    • Lift the connector latch and disconnect the power-button board cable from the system board.

  30. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 30, immagine 1 di 1
    • Lift the palm-rest assembly off the computer base.

  31. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 31, immagine 1 di 1
    • Remove the keyboard.

    • Remove the power-button board.

    • Remove the status-light board.

    • Remove the Touchpad.

  32. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Replace the touchpad.

    • Replace the status-light board.

    • Replace the power-button board.

    • Replace the keyboard.

  33. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Connect the power-button board cable to the system board.

  34. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 34, immagine 1 di 1
    • Align the palm-rest assembly on the computer base and snap it into place.

  35. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Close the display and turn the computer over.

  36. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Replace the screws that secure the palm-rest assembly to the computer base.

  37. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Connect the keyboard cable and the keyboard-backlight cable to the system board.

Linea Traguardo

Terrence15

Membro da: 12/18/17

79.031 Reputazione

441 Guide realizzate

Team

RampUP America, Inc. Membro di RampUP America, Inc.

Community

42 Membri

1.985 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 157