Aggiusta la tua roba Comunità Store

DBPOWER T20 Disassembly

Introduzione

If you need to repair anything on the DBPOWER T20 Projector you need to disassemble it first. This guide will show you all the steps necessary to disassemble the device to a point where items can be replaced. It is quite a sturdy device so don't be afraid to use some force removing the top of the device and the wired. However, use caution around the mirrors inside the device.

Cosa ti serve

  1. DBPOWER T20 Disassembly, DBPOWER T20 Disassembly: passo 1, immagine 1 di 1

    • Flip the device and lay flat.

    Modifica

  2. DBPOWER T20 Disassembly: passo 2, immagine 1 di 1

    • Remove the four (9 mm) screws with a PH2 screwdriver.

    • Remove the two (7 mm) located with a PH2 screwdriver.

    Modifica

  3. DBPOWER T20 Disassembly: passo 3, immagine 1 di 3 DBPOWER T20 Disassembly: passo 3, immagine 2 di 3 DBPOWER T20 Disassembly: passo 3, immagine 3 di 3

    • Flip the device over and pry the top off with a plastic opening tool.

    Modifica

  4. DBPOWER T20 Disassembly: passo 4, immagine 1 di 1

    • Remove the ribbon cable connecting the motherboard to the button control board by gently pulling it from its connector.

    Modifica

  6. DBPOWER T20 Disassembly: passo 5, immagine 1 di 2 DBPOWER T20 Disassembly: passo 5, immagine 2 di 2

    • Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver.

    Modifica

  7. DBPOWER T20 Disassembly: passo 6, immagine 1 di 3 DBPOWER T20 Disassembly: passo 6, immagine 2 di 3 DBPOWER T20 Disassembly: passo 6, immagine 3 di 3

    • Remove the two cables connected to the motherboard: black power cable and the red/black fan cable.

    • the black cable requires more force to remove than the other cables.

    Modifica

  8. DBPOWER T20 Disassembly: passo 7, immagine 1 di 2 DBPOWER T20 Disassembly: passo 7, immagine 2 di 2

    • Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard.

    Modifica

  9. DBPOWER T20 Disassembly: passo 8, immagine 1 di 1

    • Raise motherboard by lifting sideways and then up to avoid the ports.

    Modifica

  10. DBPOWER T20 Disassembly: passo 9, immagine 1 di 2 DBPOWER T20 Disassembly: passo 9, immagine 2 di 2

    • Remove wires attaching the piezoelectric speakers to the motherboard.

    Modifica

  11. DBPOWER T20 Disassembly: passo 10, immagine 1 di 2 DBPOWER T20 Disassembly: passo 10, immagine 2 di 2

    • Remove the five screws securing the black plastic cover with a J0 screwdriver.

    • Lift up and out to remove.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 5 altri collaboratori

Andrea Espinosa

Membro da: 02/15/18

506 Reputazione

3 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

USF Tampa, Team S16-G2, Boczar Spring 2018 Membro di USF Tampa, Team S16-G2, Boczar Spring 2018

USFT-BOCZAR-S18S16G2

5 Membri

5 Guide realizzate

4 Commenti

Anyone find a bulb for this thing? And/or know what else (or a quick fix) would fix a dark or burn mark on the image?

jcr4130 - Replica

haing the same issue tried to call a electronics repair place to see if the could order a new polarizing lens for me and they said they could not unless they were the ones that did the repair

derek_russell82308 -

Really? Well, crap

KweenBeeTX -

How are the lenses supposed to sit in the hompow t20 mini projector

Joseph Duffey - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 15

Tutti i Tempi: 2,816