Salta al contenuto principale

Introduzione

If the tripod mount has become stripped or the slots that the plastic mounts slide into become stripped, follow this guide on how to replace the mounting piece on your Contour Roam2.

Ricambi

Nessuna parte specificata.

  1. Contour Roam2 Mounting Piece Replacement, Record Slider: passo 1, immagine 1 di 1
    • Using the phillips head screwdriver (PH000) locate and remove the 4.45mm (.175in) screw by the 180 degree graphic on the metal ring.

    • The screws in the camera are very small and can strip very easily. Apply consistent pressure when removing screws.

  2. Contour Roam2 Mounting Piece Replacement: passo 2, immagine 1 di 2 Contour Roam2 Mounting Piece Replacement: passo 2, immagine 2 di 2
    • Rotate the metal ring counterclockwise until completely removed.

  3. Contour Roam2 Mounting Piece Replacement: passo 3, immagine 1 di 2 Contour Roam2 Mounting Piece Replacement: passo 3, immagine 2 di 2
    • Using the phillips head screwdriver (PH000) remove the two 4.46mm (.175in) screws on each side near the back of the camera.

  4. Contour Roam2 Mounting Piece Replacement: passo 4, immagine 1 di 3 Contour Roam2 Mounting Piece Replacement: passo 4, immagine 2 di 3 Contour Roam2 Mounting Piece Replacement: passo 4, immagine 3 di 3
    • Grab the camera on both sides and slide the outer shell forward until completely removed.

  5. Contour Roam2 Mounting Piece Replacement: passo 5, immagine 1 di 1
    • Lift the record slider out.

    • The record slider should come out easily no matter the position (forward or backward).

  6. Contour Roam2 Mounting Piece Replacement, Mounting Piece: passo 6, immagine 1 di 2 Contour Roam2 Mounting Piece Replacement, Mounting Piece: passo 6, immagine 2 di 2
    • Using the phillips head screwdriver (PH000) remove the two 3.82mm (0.150in) screws on the bottom of mounting piece near the tripod screw-in.

    • The screws in the camera are very small and can strip very easily. Apply consistent pressure when removing screws.

  7. Contour Roam2 Mounting Piece Replacement: passo 7, immagine 1 di 2 Contour Roam2 Mounting Piece Replacement: passo 7, immagine 2 di 2
    • Open the back door by your thumb and index finger on sides of back door and pull upward.

  8. Contour Roam2 Mounting Piece Replacement: passo 8, immagine 1 di 1
    • Using your thumb, pry sides outward on back of mount piece.

    • This will loosen mount piece for removal in proceeding step.

    • Side can be hard to pry outward. Using a flat tool such as a metal spudger, may help if your thumb is insufficient.

  9. Contour Roam2 Mounting Piece Replacement: passo 9, immagine 1 di 2 Contour Roam2 Mounting Piece Replacement: passo 9, immagine 2 di 2
    • Remove and replace mount piece.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Matthew Kofsky

Membro da: 11/03/2015

548 Reputazione

3 Guide realizzate

Team

Un commento

Hi i need this part...

julmarte - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 14

Tutti i Tempi: 1,169