Parti

Nessuna parte richiesta.

    • Hold the phone with the back (camera side) facing you. Slide the battery cover off of the phone.

    Aggiungi Commento

    • Pull the battery out by lifting the black tab on the left side of the battery.

    Aggiungi Commento

    • Remove the camera cover of the phone, using your light blue wedge tool.

    Aggiungi Commento

    • Unscrew the four black Torx head screws, found in each corner of the back.

    • Warning: Unscrewing the screw indicated in the picture will void any warranty on the phone.

    Aggiungi Commento

    • Unscrew the black Phillips head screw below the right speaker.

    Aggiungi Commento

    • After removing the screw, pull up on the motherboard to release it from the circuit board (green tab, see Figure 11). This will simply snap out, and does not require too much force.

    Aggiungi Commento

    • Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.

    Aggiungi Commento

    • Remove the four silver Phillips head screws from the screened half of the phone.

    Aggiungi Commento

    • Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.

    Aggiungi Commento

  1. Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    • Unscrew the four Phillips head screws that attach the screen to the front case.

    Aggiungi Commento

    • Remove the circuit board; pull it apart at the orange tab. This will detach the screen from its circuit board.

    Aggiungi Commento

    • Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.

    Aggiungi Commento

    • Place screen back into front cover.

    Aggiungi Commento

    • Screw the four smallest silver Torx head screws into the circuit board, which will attach it to the front cover.

    Aggiungi Commento

    • Feed the circuit board through the back piece.

    Aggiungi Commento

    • Use the four Phillips head silver screws to attach the back piece to the front of the phone.

    Aggiungi Commento

    • Slide the circuit board through the slot in the keyboard.

    Aggiungi Commento

    • Attach the keyboard to the sliding tracks using the four silver Torx screws.

    Aggiungi Commento

    • Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.

    Aggiungi Commento

    • Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.

    Aggiungi Commento

    • Place the back cover onto the motherboard, clicking it into place.

    Aggiungi Commento

    • Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.

    Aggiungi Commento

    • Replace the camera cover.

    Aggiungi Commento

    • Replace battery, keeping the black tab available to grab.

    Aggiungi Commento

    • Slide the battery cover back into place.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Laura Kimberly Simonds

Membro da: 24/09/2012

301 Reputazione

3 Guide realizzate

Team

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 4

Tutti i Tempi: 367