/
Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Unisciti
Accedi
Unisciti alla più grande community di riparazione al mondo
Canon Powershot SD750 Camera Case Replacement

Canon Powershot SD750 Camera Case Replacement

Memphis Wong

Memphis Wong e 12 altri collaboratori

Ultimo aggiornamento il March 1, 2016

15 - 30 minuti
Moderato
Guida Studente in Evidenza

Introduzione

Vai al passo 1

You will need a #00 Phillips screwdriver to replace the camera's casing.

Make sure to remove the batteries before beginning the guide.

Cosa ti serve

Strumenti

  1. Canon Powershot SD750 Camera Case Replacement, Camera Case: passo 1, immagine 1 di 1

    • Turn the camera to the side that has the attachment for the wrist strap.

    • Unscrew the two black 3.4 mm screws with a #00 Phillips screwdriver.

    Modifica

  2. Canon Powershot SD750 Camera Case Replacement: passo 2, immagine 1 di 1

    • Remove the plastic subsection by prying it with your fingers.

    • Note: It may be helpful to pry from the bottom of the camera with the battery door open.

    • The wrist strap attachment behind the subsection will come loose and may fall out.

    Modifica

  4. Canon Powershot SD750 Camera Case Replacement: passo 3, immagine 1 di 1

    • Turn the camera over to the side opposite of the wrist strap.

    • Remove the two silver 3.4 mm screws with a #00 Phillips screwdriver.

    Modifica

  5. Canon Powershot SD750 Camera Case Replacement: passo 4, immagine 1 di 1

    • Flip the camera upside down.

    • Remove the following screws with a #00 Phillips screwdriver.

    • One black 3.4 mm Phillips screw.

    • One silver 3.4 mm Phillips screw.

    • NOTE: Using your fingernails may help in removal.

    Modifica

  6. Canon Powershot SD750 Camera Case Replacement: passo 5, immagine 1 di 1

    • Place the camera on the side opposite of the wrist strap handle.

    • Then begin to pry the casing apart with both hands by applying pressure to the top and bottom of the camera.

    • Remove the small metal plate underneath the plastic covering and set aside. (It should be loosely attached)

    • Note: A rubber foam washer that separates the lens from the casing will fall off when the case is removed. Be sure to store it safely.

    • Note: When reassembling ensure the back plate screw tabs are over the wrist strap attachment and the front plate screw tabs go under orange casing.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 12 altri collaboratori

Memphis Wong

Membro da: 09/30/10

73 Reputazione

1 Guida realizzata

Distintivi: 10

+7 altri distintivi

Team

Cal Poly, Team 14-37, Forte Fall 2010 Membro di Cal Poly, Team 14-37, Forte Fall 2010

CPSU-FORTE-F10S14G37

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 15

Ultimi 30 Giorni: 33

Tutti i Tempi: 3,834