Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Canon PowerShot SD500 Digital ELPH Image Sensor Replacement

Cosa ti serve

  1. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, Battery: passo 1, immagine 1 di 1
    • Slide open the battery cover.

    • Push the small orange tab to the side so the battery can be removed.

  2. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 2, immagine 1 di 2 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 2, immagine 2 di 2
    • Slide the battery out of the battery compartment.

  3. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, Front and Rear Casing: passo 3, immagine 1 di 2 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, Front and Rear Casing: passo 3, immagine 2 di 2
    • Two Phillips screws need to be removed using a #00 Phillips screwdriver. The upper screw is under the USB port cover, which can simply be pulled away gently from the casing. the lower screw is visible on the panel.

    • The screws are different sizes. The .125 inch screw is located under the USB port cover. The 0.85 inch screw goes in the lower hole on the panel.

    • When looking at the back of the camera, these two screws are on the right panel of the camera.

  4. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 4, immagine 1 di 1
    • Remove the right side cover from the camera casing.

  5. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 5, immagine 1 di 1
    • Remove a .07 inch Phillips screw using a #00 Phillips screwdriver.

  6. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 6, immagine 1 di 1
    • Remove two .085 inch Phillips screws from the left side of the camera using a #00 Philips screwdriver.

  7. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 7, immagine 1 di 1
    • Remove the left side cover from the camera.

  8. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 8, immagine 1 di 1
    • Remove three .15 inch Phillips screws from the bottom of the camera using a #00 Phillips screwdriver.

  9. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 9, immagine 1 di 2 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 9, immagine 2 di 2
    • Once the casing is unscrewed, hold the camera with one side facing down, and lift the opposite face of the casing to open it.

    • Remove the internal camera components and layout out all pieces on a clean surface.

    • The front and back cover may require gentle rocking to remove.

  10. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, Button Contact Panel: passo 10, immagine 1 di 1
    • Carefully wedge the pry tool under the ribbon in the ribbon gate.

    • Gently remove the ribbon from the ribbon gate by pulling it away from the gate with the pry tool.

    • Be careful not to damage the ribbon.

  11. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 11, immagine 1 di 1
    • Gently press the ribbon back to get access to a Phillips screw behind it.

    • Be careful not to damage the ribbon.

    • Unscrew two .125 inch long Phillips screws using a #00 Philips screwdriver.

  12. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 12, immagine 1 di 3 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 12, immagine 2 di 3 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 12, immagine 3 di 3
    • Remove the ribbon with a pry tool by gently pulling it out of the ribbon gate tab.

    • Be careful not to damage the ribbon.

    • Pull the button board away from the rest of the camera.

  13. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, LCD: passo 13, immagine 1 di 1
    • Unscrew one .113 inch Phillips screw using a #00 Phillips screwdriver.

  14. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 14, immagine 1 di 1
    • Lift the LCD screen up and away from the tab that holds it in place on the face of the camera.

    • Be careful, the LCD screen is still connect to the camera by a ribbon cable.

  15. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 15, immagine 1 di 2 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 15, immagine 2 di 2
    • Gently press the pry tool under the ribbon gate and lift up to free the ribbon connecting the LCD to the circuit board.

    • Be careful not to damage the ribbon.

    • The LCD can now be completely removed from the camera.

  16. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement, Image Sensor: passo 16, immagine 1 di 1
    • Place the pry tool under ribbon gate and gently lift it up, disconnecting the ribbon.

  17. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 17, immagine 1 di 1
    • Unscrew three .15 inch Phillips screws from the back of the camera using a #00 Phillips screwdriver.

  18. Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 18, immagine 1 di 2 Canon PowerShot SD500 Digital ELPH Image Sensor Replacement: passo 18, immagine 2 di 2
    • Use the pry tool to gently lift the image sensor away from the rest of the camera.

    • Be careful not to damage the image sensor as you pry it up.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Team

Clemson, Team 2-1, Benson Fall 2014 Membro di Clemson, Team 2-1, Benson Fall 2014

CLEM-BENSON-F14S2G1

4 Membri

9 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 227