Aggiusta la tua roba Comunità Store

Canon PowerShot SD1200 IS Motherboard

Introduzione

Use this guide to access the motherboard to reseat connections on the motherboard or to remove the motherboard for replacement.

Cosa ti serve

  1. Canon PowerShot SD1200 IS Motherboard, Front and Rear Covers: passo 1, immagine 1 di 1

    • Remove the battery.

    Traduci

  2. Canon PowerShot SD1200 IS Motherboard: passo 2, immagine 1 di 3 Canon PowerShot SD1200 IS Motherboard: passo 2, immagine 2 di 3 Canon PowerShot SD1200 IS Motherboard: passo 2, immagine 3 di 3

    • Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)

    • Remove the two screws from the bottom of the camera. (4mm Phillips 00)

    • Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

    Traduci

  3. Canon PowerShot SD1200 IS Motherboard: passo 3, immagine 1 di 2 Canon PowerShot SD1200 IS Motherboard: passo 3, immagine 2 di 2

    • Pull off the front cover.

    • If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.

    • Remove the back cover.

    Traduci

  5. Canon PowerShot SD1200 IS Motherboard, Motherboard: passo 4, immagine 1 di 1

    • Remove the microphone connector by gripping it with the tool and gently, with a wiggling motion, pull it out.

    • Pull the connector straight out by the white connector. Pulling on the wires will damage them.

    Traduci

  6. Canon PowerShot SD1200 IS Motherboard: passo 5, immagine 1 di 1

    • Lift off the mechanical shutter button assembly.

    Traduci

  7. Canon PowerShot SD1200 IS Motherboard: passo 6, immagine 1 di 2 Canon PowerShot SD1200 IS Motherboard: passo 6, immagine 2 di 2

    • Use the spudger to lift the tab on the Zero Insertion Force (ZIF) connector located at the bottom of the motherboard.

    • Be sure you are prying up on the hinged retaining flap, not the connector itself.

    • Slide out the ribbon cable.

    • Use the spudger to pry up each side of the Flat-Topped Connectors

    Traduci

  8. Canon PowerShot SD1200 IS Motherboard: passo 7, immagine 1 di 1

    • Remove the press fit ribbon cable by prying upward with spudger tool.

    • It is not necessary to remove the Lens or Flash Assemblies to remove the motherboard.

    Traduci

  9. Canon PowerShot SD1200 IS Motherboard: passo 8, immagine 1 di 1

    • Remove the bottom right screw from the motherboard. (4mm Phillips 00)

    • Remove top and lower left black screws from the motherboard. (2.5mm Phillips 00)

    Traduci

  10. Canon PowerShot SD1200 IS Motherboard: passo 9, immagine 1 di 1

    • Lift out the motherboard.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 4 altri collaboratori

Jeff Casper

Membro da: 09/15/16

848 Reputazione

7 Guide realizzate

Distintivi: 18

+15 altri distintivi

Team

USF Tampa, Team 17-5, Blackwell Fall 2016 Membro di USF Tampa, Team 17-5, Blackwell Fall 2016

USFT-BLACKWELL-F16S17G5

3 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 11

Tutti i Tempi: 394