Parti

Nessuna parte richiesta.

Remove the two screws from the side panel closest to the camera lens.
  • Remove the two screws from the side panel closest to the camera lens.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

Remove the two screws from the camera bottom panel.
  • Remove the two screws from the camera bottom panel.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

  • Remove the 2 screws from the side panel farthest from the lens.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

  • Pull the back panel away from the camera body, starting at the end with the function buttons.

Aggiungi Commento

  • Remove the small cover panel and attached wrist strap mount.

Aggiungi Commento

  • Remove the front cover by gently pulling it away from the camera body.

Aggiungi Commento

  • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Aggiungi Commento

  • Remove the 2 screws located at the top of the LCD panel.

  • Note: These screws are 2.4 mm long.

Aggiungi Commento

  • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

Aggiungi Commento

  • Push the metal frame away from the metal tab using the spudger, to detach the frame.

  • Rotate the metal frame upwards.

  • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Aggiungi Commento

  • Carefully lift the metal frame from the camera.

  • Remove the black LCD screen, leaving the thin lens pieces in place.

  • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

Aggiungi Commento

  • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

  • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

  • Note: Tweezers are helpful to disconnect the ribbon

Aggiungi Commento

  • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

Aggiungi Commento

  • Remove the screw securing the flash assembly.

  • Note: The screw is 2.4mm long.

Aggiungi Commento

  • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

Aggiungi Commento

  • Remove the flash assembly.

  • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

Aggiungi Commento

  • Using the spudger, take off the shutter button by prying the small tab on the front side of the camera.

Aggiungi Commento

  • Remove the 2.90mm screw from the lens, near the motherboard.

Aggiungi Commento

  • Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

Aggiungi Commento

  • With a spudger disconnect the orange connector ribbon as shown.

  • Disconnect the orange connector ribbon that is located under the now removed shutter button.

Aggiungi Commento

  • Remove the two 2.90 mm screws from the motherboard.

Aggiungi Commento

  • With Tweezers detach the bottom orange ribbon.

Aggiungi Commento

  • Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

Aggiungi Commento

  • With spudger gently remove the Viewfinder Window that is directly above the lens.

Remove screw attaching viewfinder piece to lens framing.

Adam Biesok - Replica

  • Detach the mother board with lens from body of camera.

  • Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.

  • Your lens has been removed from the motherboard and bottom framing.

Aggiungi Commento

  • The motherboard (left) is now separated from the lens.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Phillip Phung

Membro da: 19/01/2012

486 Reputazione

9 Guide realizzate

Team

Cal Poly, Team 8-18, Maness Winter 2012 Membro di Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Membri

10 Guide realizzate

Which part is the CCD sensor?

yakksoho - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 7

Ultimi 30 Giorni: 39

Tutti i Tempi: 4,835