Salta al contenuto principale

Canon PowerShot SD1000 LCD Screen Replacement

Cosa ti serve

  1. Canon PowerShot SD1000 LCD Screen Replacement, Back Panel: passo 1, immagine 1 di 2 Canon PowerShot SD1000 LCD Screen Replacement, Back Panel: passo 1, immagine 2 di 2
    • Remove the two 2.9 mm screws from the side panel closest to the camera lens.

  2. Canon PowerShot SD1000 LCD Screen Replacement: passo 2, immagine 1 di 1
    • Remove the two 2.9 mm screws from the camera bottom panel.

  3. Canon PowerShot SD1000 LCD Screen Replacement: passo 3, immagine 1 di 1
    • Remove the two 2.9 mm screws from the side panel farthest from the lens.

  4. Canon PowerShot SD1000 LCD Screen Replacement: passo 4, immagine 1 di 1
    • Pull the back panel away from the camera body, starting at the end with the function buttons.

  5. Canon PowerShot SD1000 LCD Screen Replacement: passo 5, immagine 1 di 1
    • Remove the small cover panel and the attached wrist strap mount.

  6. Canon PowerShot SD1000 LCD Screen Replacement, Front Case: passo 6, immagine 1 di 1
    • Remove the front cover by gently pulling it away from the camera body.

  7. Canon PowerShot SD1000 LCD Screen Replacement: passo 7, immagine 1 di 1
    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

  8. Canon PowerShot SD1000 LCD Screen Replacement, LCD Screen: passo 8, immagine 1 di 1
    • Remove the two 2.4 mm screws located at the top of the LCD panel.

  9. Canon PowerShot SD1000 LCD Screen Replacement: passo 9, immagine 1 di 2 Canon PowerShot SD1000 LCD Screen Replacement: passo 9, immagine 2 di 2
    • Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

  10. Canon PowerShot SD1000 LCD Screen Replacement: passo 10, immagine 1 di 1
    • Push the metal frame away from the metal tab using the spudger to detach the frame.

    • Rotate the metal frame upwards.

    • The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

  11. Canon PowerShot SD1000 LCD Screen Replacement: passo 11, immagine 1 di 2 Canon PowerShot SD1000 LCD Screen Replacement: passo 11, immagine 2 di 2
    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

  12. Canon PowerShot SD1000 LCD Screen Replacement: passo 12, immagine 1 di 3 Canon PowerShot SD1000 LCD Screen Replacement: passo 12, immagine 2 di 3 Canon PowerShot SD1000 LCD Screen Replacement: passo 12, immagine 3 di 3
    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Tweezers are helpful to disconnect the ribbon.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Team

Cal Poly, Team 8-18, Maness Winter 2012 Membro di Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Membri

12 Guide realizzate

Un commento

Very helpful. These units still sell for a lot more than the cost of the replacement LCD

George Francis - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 40

Tutti i Tempi: 3,482