Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Canon EOS Rebel T6i Flash Assembly Replacement

Introduzione

This guide will show the steps to in replacing the Flash assembly on the top of the camera.

Cosa ti serve

  1. Canon EOS Rebel T6i Flash Assembly Replacement, Flash Assembly: passo 1, immagine 1 di 3 Canon EOS Rebel T6i Flash Assembly Replacement, Flash Assembly: passo 1, immagine 2 di 3 Canon EOS Rebel T6i Flash Assembly Replacement, Flash Assembly: passo 1, immagine 3 di 3

    • Remove all visible exterior screws:

    • Two 6.84 mm screws on the right side

    • Six 5.33 mm screws

    Traduci

  2. Canon EOS Rebel T6i Flash Assembly Replacement: passo 2, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 2, immagine 2 di 2

    • One 5.91 mm screw on the top right.

    • One 3.39 mm screw on the top left.

    Traduci

  3. Canon EOS Rebel T6i Flash Assembly Replacement: passo 3, immagine 1 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 3, immagine 2 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 3, immagine 3 di 3

    • Locate the rubber grip on the left side of the camera. Using a metal spudger, pry the rubber grip off of the casing.

    • Be careful not to rip the rubber with the metal spudger.

    • Remove the five silver screws underneath the grip.

    • One 5.83mm silver DL Flap

    • Four 5.85mm silver under flap

    Traduci

  4. Canon EOS Rebel T6i Flash Assembly Replacement: passo 4, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 4, immagine 2 di 2

    • Using the same metal spudger as before, pry the rubber grip located just below the turndial. Again, careful not to rip the rubber.

    Traduci

  5. Canon EOS Rebel T6i Flash Assembly Replacement: passo 5, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 5, immagine 2 di 2

    • Carefully use the plastic opening tool to pry the casing apart along the seam.

    • Follow the seem with the plastic tool until the back is ready to remove.

    • Before you move on, Make sure you use the grounding strip to remove the chance of discharging static electricity into the internal components.

    Traduci

  7. Canon EOS Rebel T6i Flash Assembly Replacement: passo 6, immagine 1 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 6, immagine 2 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 6, immagine 3 di 3

    • Notice the two connections attaching the back of the camera to the motherboard.

    • To disconnect the white wire, pinch the wire casing and pull directly out from the camera. It will take a very small amount of elbow grease. However, do not force or pry it.

    • To disconnect the ribbon connector, softly pull the back away from the motherboard. It should come undone with little force.

    • Once removed, set the back in a safe place.

    Traduci

  8. Canon EOS Rebel T6i Flash Assembly Replacement: passo 7, immagine 1 di 1

    • Now to remove all of the bottom ribbon connectors.

    Traduci

  9. Canon EOS Rebel T6i Flash Assembly Replacement: passo 8, immagine 1 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 8, immagine 2 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 8, immagine 3 di 3

    • To remove the Ribbon connectors that have a locking mechanism, identify the flap on the ribbon connector. Use either needle nose tweezers, or a plastic wedge to flip the small flap to the "up" position.

    • Once the flap is up, use the plastic spudger to pull the ribbon connector out of the connection using the hole in the center of the ribbon.

    • Now is a good time to remove the small backup battery from the motherboard.

    Traduci

  10. Canon EOS Rebel T6i Flash Assembly Replacement: passo 9, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 9, immagine 2 di 2

    • Disconnect the small plastic connections on the top left corner of the motherboard by gripping the small plastic portion of the wire and gently pulling out of the connection.

    • Go ahead and disconnect all of the ribbon connections along the top that you can get to. Don't worry about the underneath connections or the ribbon connections with the foam block, as these will be removed later.

    Traduci

  11. Canon EOS Rebel T6i Flash Assembly Replacement: passo 10, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 10, immagine 2 di 2

    • Now its time to remove the rest of the casing.

    • Remove the four crews from the front of the camera. There are two screws above the lens mount and two screws inside the lens mount.

    • Remove the four screws left on the bottom.

    • Now the front is ready to be removed.

    Traduci

  12. Canon EOS Rebel T6i Flash Assembly Replacement: passo 11, immagine 1 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 11, immagine 2 di 3 Canon EOS Rebel T6i Flash Assembly Replacement: passo 11, immagine 3 di 3

    • Using the plastic wedge, pry the front of the casing off the camera.

    • Electric shock Warning!! Be careful not to touch the terminals of the capacitor, as this can cause the capacitor to discharge.

    • Set the front aside, preferably in a safe place.

    Traduci

  13. Canon EOS Rebel T6i Flash Assembly Replacement: passo 12, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 12, immagine 2 di 2

    • Remove the yellow and red connections on the front near the black cylinder (capacitor).

    • The yellow connector will just pop out if pried from the bottom using a plastic wedge.

    • The red connector will pull out of the casing with either a plastic wedge or a thin set of tweezers.

    • Electric shock Warning!! be careful not to touch the terminals of the capacitor, as this can cause the capacitor to discharge.

    Traduci

  14. Canon EOS Rebel T6i Flash Assembly Replacement: passo 13, immagine 1 di 1

    • Remove the viewfinder adjustment knob with a screwdriver. Once this screw is out, the entire flash assembly is ready to be removed.

    Traduci

  15. Canon EOS Rebel T6i Flash Assembly Replacement: passo 14, immagine 1 di 2 Canon EOS Rebel T6i Flash Assembly Replacement: passo 14, immagine 2 di 2

    • Remove the entire upper piece of the casing. This is the flash assembly and is sold as a single piece. This piece should easily pull up and off the camera casing.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 35

Tutti i Tempi: 3,395