Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Canon EOS 300 Bottom Panel Replacement

Cosa ti serve

  1. Canon EOS 300 Bottom Panel Replacement, Batteries: passo 1, immagine 1 di 3 Canon EOS 300 Bottom Panel Replacement, Batteries: passo 1, immagine 2 di 3 Canon EOS 300 Bottom Panel Replacement, Batteries: passo 1, immagine 3 di 3
    • Open up the battery door.

  2. Canon EOS 300 Bottom Panel Replacement: passo 2, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement: passo 2, immagine 2 di 2
    • Remove the batteries from the camera by sliding them out into your palm.

  3. Canon EOS 300 Bottom Panel Replacement, Side Panel with Lever: passo 3, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement, Side Panel with Lever: passo 3, immagine 2 di 2
    • Release the side latch to open the back panel.

  4. Canon EOS 300 Bottom Panel Replacement: passo 4, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement: passo 4, immagine 2 di 2
    • Remove the two black 4.5mm screws above and below the latch.

  5. Canon EOS 300 Bottom Panel Replacement: passo 5, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement: passo 5, immagine 2 di 2
    • Using your finger, carefully pry open the side panel from the top of camera.

    • Pull panel downwards to remove.

    • Make sure to keep track of the small black piece of rubber under the latch.

  6. Canon EOS 300 Bottom Panel Replacement, Front Panel: passo 6, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement, Front Panel: passo 6, immagine 2 di 2
    • Remove the two silver 6mm Phillips #1 screws.

  7. Canon EOS 300 Bottom Panel Replacement: passo 7, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement: passo 7, immagine 2 di 2
    • Flip camera over to the bottom.

    • Remove the one 5mm Phillips #1 silver screw.

  8. Canon EOS 300 Bottom Panel Replacement: passo 8, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement: passo 8, immagine 2 di 2
    • Remove the front panel by pulling away from the side with the lever.

  9. Canon EOS 300 Bottom Panel Replacement, Bottom Panel: passo 9, immagine 1 di 2 Canon EOS 300 Bottom Panel Replacement, Bottom Panel: passo 9, immagine 2 di 2
    • Remove three black 7.3mm Phillips #1 screws located on the corners of the camera.

    • Remove five black 4.8mm Phillips #1 screws.

  10. Canon EOS 300 Bottom Panel Replacement: passo 10, immagine 1 di 3 Canon EOS 300 Bottom Panel Replacement: passo 10, immagine 2 di 3 Canon EOS 300 Bottom Panel Replacement: passo 10, immagine 3 di 3
    • Simply remove the bottom panel by prying it off with your finger.

    • When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out.

    • Be wary of a loose piece of foam attached to the bottom panel.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Tammy Kong

Membro da: 01/23/14

771 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 6-20, Maness Winter 2014 Membro di Cal Poly, Team 6-20, Maness Winter 2014

CPSU-MANESS-W14S6G20

4 Membri

32 Guide realizzate

Un commento

muy buena la explicacion de como desmontar la maquina. Te has gadano los 30 puntos

Ricardo Alonso Gurrea - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 7

Tutti i Tempi: 649