Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • Turn the device upside down.

    • Using your finger, slide the silver cover release button towards the top of the device.

    • Lift and remove the back cover.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 1
    • Using your fingernails, lift the sides of the battery.

    • Remove the battery.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • Orient the device so that the screen is facing the ground.

    • Using your finger, gently lift the top of the SIM card.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 1
    • Gently pull out the SIM card.

    • The card will break in half if you apply too much force when pulling out the card.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 1
    • Using a T6 Torx screwdriver, remove the four screws from the bottom half of the device.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 1
    • Orient the device so that the screen is facing you.

    • Using a spudger, remove the ear piece cover.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Using a T6 Torx screwdriver, remove the two screws from the top corners of the device.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 1
    • Remove the back chassis by gently pulling the chassis back and forth.

    • The headphone jack can break if the chassis is pulled too forcefully.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 1
    • Orient the device so that the screen is facing the ground, and the top of the phone is facing you.

    • Using a pair of tweezers, lift and remove the following:

    • The two round connectors on the top of the mother board.

    • The round connectors are hooked into the mother board.

    • The flat connector in the lower corner of the mother board.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • Using your fingers, carefully lift and remove the mother board.

    • The connectors underneath the mother board are delicate and easily damaged.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Using a pair of tweezers, remove the three ribbon connectors.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 1
    • Remove the mother board by lifting the board upward.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 2 : passo 13, immagine 2 di 2
    • Using a pry tool, lift up on the four tabs located on the edges of the faceplate.

    • Remove the faceplate by lifting the plate upward.

Linea Traguardo

Altre 2 persone hanno completato questa guida.

Ryan

Membro da: 03/12/12

696 Reputazione

11 Guide realizzate

Team

Clemson, Team 2-5, Benson Spring 2012 Membro di Clemson, Team 2-5, Benson Spring 2012

CLEM-BENSON-S12S2G5

2 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 5

Tutti i Tempi: 2,383