Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Blackberry Bold 9650 Faceplate Replacement

Cosa ti serve

  1. Blackberry Bold 9650 Faceplate Replacement, Battery: passo 1, immagine 1 di 2 Blackberry Bold 9650 Faceplate Replacement, Battery: passo 1, immagine 2 di 2
    • Turn the device upside down.

    • Using your finger, slide the silver cover release button towards the top of the device.

    • Lift and remove the back cover.

  2. Blackberry Bold 9650 Faceplate Replacement: passo 2, immagine 1 di 1
    • Using your fingernails, lift the sides of the battery.

    • Remove the battery.

  3. Blackberry Bold 9650 Faceplate Replacement, SIM Card: passo 3, immagine 1 di 1
    • Orient the device so that the screen is facing the ground.

    • Using your finger, gently lift the top of the SIM card.

  4. Blackberry Bold 9650 Faceplate Replacement: passo 4, immagine 1 di 1
    • Gently pull out the SIM card.

    • The card will break in half if you apply too much force when pulling out the card.

  5. Blackberry Bold 9650 Faceplate Replacement, Back Chassis: passo 5, immagine 1 di 1
    • Using a T6 Torx screwdriver, remove the four screws from the bottom half of the device.

  6. Blackberry Bold 9650 Faceplate Replacement: passo 6, immagine 1 di 1
    • Orient the device so that the screen is facing you.

    • Using a spudger, remove the ear piece cover.

  7. Blackberry Bold 9650 Faceplate Replacement: passo 7, immagine 1 di 1
    • Using a T6 Torx screwdriver, remove the two screws from the top corners of the device.

  8. Blackberry Bold 9650 Faceplate Replacement: passo 8, immagine 1 di 1
    • Remove the back chassis by gently pulling the chassis back and forth.

    • The headphone jack can break if the chassis is pulled too forcefully.

  9. Blackberry Bold 9650 Faceplate Replacement, Mother Board: passo 9, immagine 1 di 1
    • Orient the device so that the screen is facing the ground, and the top of the phone is facing you.

    • Using a pair of tweezers, lift and remove the following:

    • The two round connectors on the top of the mother board.

    • The round connectors are hooked into the mother board.

    • The flat connector in the lower corner of the mother board.

  10. Blackberry Bold 9650 Faceplate Replacement: passo 10, immagine 1 di 1
    • Using your fingers, carefully lift and remove the mother board.

    • The connectors underneath the mother board are delicate and easily damaged.

  11. Blackberry Bold 9650 Faceplate Replacement: passo 11, immagine 1 di 1
    • Using a pair of tweezers, remove the three ribbon connectors.

  12. Blackberry Bold 9650 Faceplate Replacement: passo 12, immagine 1 di 1
    • Remove the mother board by lifting the board upward.

  13. Blackberry Bold 9650 Faceplate Replacement, Faceplate: passo 13, immagine 1 di 2 Blackberry Bold 9650 Faceplate Replacement, Faceplate: passo 13, immagine 2 di 2
    • Using a pry tool, lift up on the four tabs located on the edges of the faceplate.

    • Remove the faceplate by lifting the plate upward.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Ryan

Membro da: 03/12/12

696 Reputazione

11 Guide realizzate

Team

Clemson, Team 2-5, Benson Spring 2012 Membro di Clemson, Team 2-5, Benson Spring 2012

CLEM-BENSON-S12S2G5

2 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 6

Tutti i Tempi: 2,383