Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 3 : passo 1, immagine 2 di 3 : passo 1, immagine 3 di 3
    • Apply pressure to the lock button on the back of the device.

    • Slide the battery cover down towards the bottom of the device, revealing the battery compartment.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 3 : passo 2, immagine 2 di 3 : passo 2, immagine 3 di 3
    • Locate groove along the right side of the battery compartment.

    • Remove battery by prying between the battery and the groove.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • Slide the SIM card holder to the left to unlock the SIM card.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Lift the SIM card holder up.

    • Gently remove the SIM card from the SIM card holder by sliding the card along the railing.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 1
    • Locate the four screws along the perimeter of the back casing.

    • Remove the four top screws using a T-6 torx screwdriver.

    • The top four screws are .413 inches.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Locate two screws within the lower edge of the inner compartment.

    • Remove the two bottom screws using a T-6 torx screwdriver.

    • The bottom two screws are .2 inches in length.

    • The second picture displays the device after the six screws have been removed.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Use the plastic opening tool to apply pressure on the two clips that are located at the bottom of the phone.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 3 : passo 8, immagine 2 di 3 : passo 8, immagine 3 di 3
    • Remove the back casing from the phone by lifting the unhooked portion, then slide the casing towards the top of the device.

    • Make sure all clips holding the case together are unhooked, so no damage is caused to the case.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • Locate on the backside of the phone, a screw towards the top of the device.

    • Using a T-6 screwdriver, remove the screw.

    • After the screw has been removed, carefully lift the side button brace to reveal the side button.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • To remove the phone's internals, start by loosening one side by pulling gently.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • With one side loosened, simply lift the phone internals to separate from the front casing.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 1
    • Turn the internals over to reveal the LCD display.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 2 : passo 13, immagine 2 di 2
    • Peel off the rubber keypad buttons from the face plate.

Linea Traguardo

Altre 2 persone hanno completato questa guida.

kmathew

Membro da: 10/17/09

3 Reputazione

5 Guide realizzate

Team

Cal Poly, Team 19-6, Maness Fall 2009 Membro di Cal Poly, Team 19-6, Maness Fall 2009

CPSU-MANESS-F09S19G6

5 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 4

Tutti i Tempi: 3,842