Aggiusta la tua roba Comunità Store

Black and Decker Pivot Plus PD600 Battery Replacement

Introduzione

If your drill stops working and the battery stops holding a charge chances are you need a new battery. You can find a replacement parts including the battery under the replacement part links in the device page. This guide will show you how to install this new battery.

Cosa ti serve

  1. Black and Decker Pivot Plus PD600 Battery Replacement, Drill: passo 1, immagine 1 di 3 Black and Decker Pivot Plus PD600 Battery Replacement, Drill: passo 1, immagine 2 di 3 Black and Decker Pivot Plus PD600 Battery Replacement, Drill: passo 1, immagine 3 di 3

    • Remove the nine 15mm Philips #1 screws

    • Remove the two 12.5mm Philips #1 screws

    • Remove the two 10mm Philips #1 screws

    Traduci

  2. Black and Decker Pivot Plus PD600 Battery Replacement: passo 2, immagine 1 di 1

    • Lift one side of the drill casing off of the drill. Note that the drill casing consists of two pieces on either side of the drill.

    Traduci

  4. Black and Decker Pivot Plus PD600 Battery Replacement, Battery: passo 3, immagine 1 di 1

    • Locate the battery and remove it from its slot at the end of the drill opposite the motor. It should be at the butt of the drill by the handle.

    Traduci

  5. Black and Decker Pivot Plus PD600 Battery Replacement: passo 4, immagine 1 di 1

    • Unplug the battery by pulling out both the red and black wires. They should come out easily with a little bit of force.

    • But be careful not to disconnect the wire from the metal it is attached to. In order to avoid this, pull the wire out by holding on to the metal part instead of just the wire.

    Traduci

  6. Black and Decker Pivot Plus PD600 Battery Replacement: passo 5, immagine 1 di 1

    • Now take the replacement battery and slide the metal parts of the wire into the metal part of the battery.

    • Make sure that the red wire connects to the curved end of the battery, and that the black wire connects to the straight end of the battery.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 9 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Jonathon Centofranchi

Membro da: 04/19/13

307 Reputazione

3 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

Cal Poly, Team 4-15, Maness Spring 2013 Membro di Cal Poly, Team 4-15, Maness Spring 2013

CPSU-MANESS-S13S4G15

5 Membri

6 Guide realizzate

9 Commenti

this drill adapter, why "6V" and the adapter body is marked 9VAC output? which is true output?

Can someone test the output and tell me the voltage? VDC? VAC? thankyou.

u411323 - Replica

B+D sell the replacement for ~$17

http://servicenet.blackanddecker.com/Par...

scottlhertzoglion -

Unfortunately I do not own the drill anymore so I can't test its output. I do know that the battery used is 6V, so I would assume that is the output. Hopes this helps!

Jonathon Centofranchi - Replica

Where can I buy the replacement battery pack for less than replacing the tool?

shgarceau - Replica

Well, I just checked B & D's web site and can buy a battery pack for $17.95 PLUS $10.99 shipping (cheapest offered).

I think buying a new one is a better idea.

shgarceau - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 50

Ultimi 30 Giorni: 157

Tutti i Tempi: 28,254