Salta al contenuto principale

Black and Decker BL3000S button panel replacement

Cosa ti serve

  1. Black and Decker BL3000S button panel replacement, Blender Base: passo 1, immagine 1 di 2 Black and Decker BL3000S button panel replacement, Blender Base: passo 1, immagine 2 di 2
    • Before disassembling the blender base, make sure the blender disconnected from any power outlet.

    • Lift the jar straight up from the base without tilting the jar.

  2. Black and Decker BL3000S button panel replacement: passo 2, immagine 1 di 1
    • Remove the top three 1/4 inch base screws using a Philip's head screwdriver.

  3. Black and Decker BL3000S button panel replacement: passo 3, immagine 1 di 2 Black and Decker BL3000S button panel replacement: passo 3, immagine 2 di 2
    • Remove the two base leg covers next to the power cord using pliers or a flat-head screwdriver.

    • This provides access to the base screws beneath.

  4. Black and Decker BL3000S button panel replacement: passo 4, immagine 1 di 1
    • Remove the following screws that secure the top and bottom halves of the base.

    • One 1/4 Phillips screw

    • One TA-20 screw

    • Both screwdrivers must have a minimum of a three inch shank (length).

    • Screwdrivers with extenders will not fit down the access holes.

  5. Black and Decker BL3000S button panel replacement: passo 5, immagine 1 di 1
    • Lift the top half of the base from the bottom half of the base to reveal the internal mechanism.

  6. Black and Decker BL3000S button panel replacement, Circuit Board: passo 6, immagine 1 di 1
    • Once you have the base removed, the circuit board should be clearly visible inside.

  7. Black and Decker BL3000S button panel replacement: passo 7, immagine 1 di 2 Black and Decker BL3000S button panel replacement: passo 7, immagine 2 di 2
    • Remove the four screws located on the circuit board.

    • Two are on the left side.

    • Two are on the right side.

  8. Black and Decker BL3000S button panel replacement: passo 8, immagine 1 di 1
    • Remove the following soldered connections with a soldering iron:

    • Motor wires

    • Power cord wires

  9. Black and Decker BL3000S button panel replacement: passo 9, immagine 1 di 1
    • Lift the circuit board straight up to remove it from the base.

  10. Black and Decker BL3000S button panel replacement, Buttons: passo 10, immagine 1 di 1
    • Once the circuit board has been freed from its screws it can be moved out of the way to gain access to the buttons.

    • A single screw must be removed from the top as shown.

  11. Black and Decker BL3000S button panel replacement: passo 11, immagine 1 di 1
    • Push firmly from the outside of the blender on the face of the buttons to pop it out of its locked position.

  12. Black and Decker BL3000S button panel replacement: passo 12, immagine 1 di 2 Black and Decker BL3000S button panel replacement: passo 12, immagine 2 di 2
    • Provided is a front and a back view of a functioning button frame from the BL3000S.

    • Check for cracks, bends, debris, or missing extentions and fastens.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Austin Abernathy

Membro da: 10/05/12

18 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 6-34, Regan Fall 2012 Membro di Cal Poly, Team 6-34, Regan Fall 2012

CPSU-REGAN-F12S6G34

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 13

Tutti i Tempi: 2,360