Introduzione

The ball bearings reduce the friction caused by the rotating wheel by concentrating it on rolling bearings, in this case there are ten on each side of the axle. Well maintained ball bearings will help the wheel spin more freely and allow for an easier and smoother ride.

Notes:

  • When cleaning the bearings and cones, solvents like kerosene can be very effective, however, just a wipe down with a rag is sufficient.
  • When the wheel is assembles correctly there should be very little resistance between the axle and the wheel and each should spin freely of the other.
  • Some of these steps require near-perfect alignment. They may take several tries to get right, so patience is a must.

Strumenti

Parti

Nessuna parte richiesta.

  1. Flip the quick release lever on the wheel.
    • Flip the quick release lever on the wheel.

    Aggiungi Commento

  2. Squeeze the brake arms together and lift the brake cable from the caliper arms.
    • Squeeze the brake arms together and lift the brake cable from the caliper arms.

    Aggiungi Commento

    • Hold the wheel to the ground, and pull the bike frame up and away to remove the wheel from the bike.

    Aggiungi Commento

    • Unscrew the quick release nut from the quick release axle. Remove the quick release axle.

    • After removing the axle you should notice that there are two springs on it. Be careful not to lose these.

    Aggiungi Commento

    • Fit the cone wrench to the cone, and fit the open end wrench to the top lock nut. Hold the cone in place with the cone wrench and turn the open end wrench to loosen and remove the top lock nut.

    • Keep track of which side each lock nut goes on. The order is important because the threading for each nut is specific for each side.

    Aggiungi Commento

    • Unscrew the cone, and set it aside.

    • Keep track of which side each cone goes on. The order is important because the threading for each cone is specific for each side.

    Aggiungi Commento

    • Remove the axle and all ball bearings.

    • Caution: There are 10 ball bearings on each side, be careful not to lose any if you plan on putting the old ones back in!

    Aggiungi Commento

    • Inspect cone surfaces and all ball bearings for dents, cracks or blemishes.

    • If any are damaged, replace them.

    Aggiungi Commento

    • Clean bearings, the bearing races, and cones by wiping them off with a rag.

    Aggiungi Commento

    • Liberally apply grease to the bearings, races, and cones.

    Aggiungi Commento

    • Insert the axle back into the wheel, with the still attached nut and cone on the bottom side of the wheel.

    Aggiungi Commento

    • Insert 10 bearings into the topmost bearing races.

    • Make sure that you insert exactly 10. If you insert too many or too few, it can damage the bearings.

    Aggiungi Commento

    • Carefully drop the axle out from the bottom of the wheel.

    • Re-insert the axle from the top side of the wheel, so that the attached nut and bearing and cone set are now sticking out of the top.

    • Now flip the wheel upside down.

    Aggiungi Commento

    • Insert the remaining 10 bearings into the bearing races on the opposite side.

    • Caution: make sure you insert exactly 10 bearings into each bearing race.

    Aggiungi Commento

    • Hand tighten bearing cone onto the free end of the axle, so that it touches the bearings without putting any pressure on them.

    • Ideally, there should be no movement or give in the axle when you pull on it or try to wiggle it. Additionally, the axle should be able to spin freely in the wheel, with minimal resistance.

    Aggiungi Commento

    • Slide the washer onto the axle.

    • Hand tighten the lock nut against the cone and washer.

    Aggiungi Commento

    • Once in proper position, use the cone wrench and open wrench to tighten the lock nut.

    • Tighten the lock nut VERY tightly. Otherwise the wheel can come out of alignment while you are riding.

    Aggiungi Commento

    • Check the way that the axle spins in the wheel. The action should be smooth, with virtually no slop when wiggled. If it is to tight or too sloppy then you need to repeat the previous step.

    Aggiungi Commento

    • Reinsert the quick release axle, and put the wheel back on the bike.

    • The springs should have the smaller tapered end closest to the hub

    Aggiungi Commento

Linea Traguardo

Altre 2 persone hanno completato questa guida.

Tyler Parra

Membro da: 10/10/2010

409 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 5-13, Maness Fall 2010 Membro di Cal Poly, Team 5-13, Maness Fall 2010

CPSU-MANESS-F10S5G13

4 Membri

11 Guide realizzate

Display and text were really helpful. I was wondering what happened to the sprocket assembly. from steps 1 through 3. This worked fine for the front wheel when I did it, but I'm not sure about working on the rear wheel. Does the sprocket assembly stay on the axle when you take off the lock nut and cone from the other side? Thanks Bob

Bob Walsh - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 56

Tutti i Tempi: 15,240