Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the phone over so that the screen is facing down. Slide the opening tool between the micro-USB port and the back cover.
    • Flip the phone over so that the screen is facing down.

    • Slide the opening tool between the micro-USB port and the back cover.

    • Use the opening tool to create a gap.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use your thumb to pry off the back panel once the gap is large enough.
    • Use your thumb to pry off the back panel once the gap is large enough.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Once the back panel is off, locate the indent at the bottom of the battery.
    • Once the back panel is off, locate the indent at the bottom of the battery.

    • Use your thumb to slip the battery out of the case.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the Phillips #00 bit to undo the nine 1.5mm screws from the back of the device. Use the Phillips #00 bit to undo the nine 1.5mm screws from the back of the device.
    • Use the Phillips #00 bit to undo the nine 1.5mm screws from the back of the device.

  5. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora
  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Wedge the opening tool into the seam of between the screen and the gray frame.
    • Wedge the opening tool into the seam of between the screen and the gray frame.

    • Run the opening tool along the seam to release the clips that hold the two pieces together.

    • You may need to use the opening picks to prevent the clips from re-engaging.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Once all the clips have been released, lift the frame and set it aside.
    • Once all the clips have been released, lift the frame and set it aside.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the Phillips #00 Phillips bit to undo the two 1.5mm screws from the motherboard. Use the Phillips #00 Phillips bit to undo the two 1.5mm screws from the motherboard.
    • Use the Phillips #00 Phillips bit to undo the two 1.5mm screws from the motherboard.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the tweezers to peel away the mesh tape and reveal the ribbon connectors. Use the tweezers to lift the brown and black tabs to release the ribbon cables and unlock them. Use the tweezers to lift the brown and black tabs to release the ribbon cables and unlock them.
    • Use the tweezers to peel away the mesh tape and reveal the ribbon connectors.

    • Use the tweezers to lift the brown and black tabs to release the ribbon cables and unlock them.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The ribbon cables should be free. Pull back on the ribbons to release them from their connectors.
    • The ribbon cables should be free. Pull back on the ribbons to release them from their connectors.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slowly lift the vibration motor away from the frame and peel up the tape.
    • Slowly lift the vibration motor away from the frame and peel up the tape.

Linea Traguardo

Un'altra persona ha completato questa guida.

Team

USF Tampa, Team S1-G2, Nance Fall 2017 Membro di USF Tampa, Team S1-G2, Nance Fall 2017

USFT-NANCE-F17S1G2

4 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 262