Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Power down the laptop using the device's power button in  top right corner of the keyboard. Ensure that the device's power cord is disconnected.
    • Power down the laptop using the device's power button in top right corner of the keyboard. Ensure that the device's power cord is disconnected.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the laptop over so the back panel is displayed.
    • Flip the laptop over so the back panel is displayed.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a Phillips #1 screwdriver, remove the ten screws from the back panel.
    • Using a Phillips #1 screwdriver, remove the ten screws from the back panel.

    • Remove the two battery screws (15.6 mm)

    • Two top corner screws (12.5 mm)

    • Six case screws (9.7mm)

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the laptop back over and open it, revealing the screen and keyboard.
    • Flip the laptop back over and open it, revealing the screen and keyboard.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using the blue plastic opening tool, wedge and loosen the seal all the way around the edges. Carefully lift up the keyboard panel.
    • Using the blue plastic opening tool, wedge and loosen the seal all the way around the edges. Carefully lift up the keyboard panel.

    • When lifting the keyboard panel, do not lift it all the way as the two connection ribbons to the motherboard must be disconnected.

    • It is recommended to break the seal of the case starting at the upper corners closest to the display monitor .

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Observe where the ribbons connect to the motherboard, there are two connections. Each connection has a black clamp. To remove the ribbon, lift the black clamp up to disconnect it.
    • Observe where the ribbons connect to the motherboard, there are two connections. Each connection has a black clamp. To remove the ribbon, lift the black clamp up to disconnect it.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Very carefully, remove the batteries with the blue plastic iFixit opening tool. Focus removing the battery near the highlighted area.
    • Very carefully, remove the batteries with the blue plastic iFixit opening tool. Focus removing the battery near the highlighted area.

    • The batteries should all be connected to one another and come out of the device as a single unit.

    • Be careful not to rip any of the black plastic covering the batteries. Exposed battery parts can lead to explosions. If the case is ripped, re-wrap them, or properly dispose of them. Do not reuse them.

  8. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora
  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The Disk Drive is located within the upper right hand corner of the laptop.
    • The Disk Drive is located within the upper right hand corner of the laptop.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a Phillips #0 screwdriver, remove the two screws (5.6 mm) around the disc drive.
    • Using a Phillips #0 screwdriver, remove the two screws (5.6 mm) around the disc drive.

    • Note which screws go where. The two smaller screws fasten onto the disc drive, while the three larger screws secure the drive on the outside.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the Phillips #00 screwdriver to remove the two screws (2.7 mm) on the side of the disc drive fastener.
    • Use the Phillips #00 screwdriver to remove the two screws (2.7 mm) on the side of the disc drive fastener.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    After removing the seven screws, lift the metal fastener from the disc drive with the plastic opening tool.
    • After removing the seven screws, lift the metal fastener from the disc drive with the plastic opening tool.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the disc drive to the right, removing it from the laptop case.
    • Slide the disc drive to the right, removing it from the laptop case.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The fan is located near the upper left hand corner of the device, connected to the motherboard and right beneath the wireless card.
    • The fan is located near the upper left hand corner of the device, connected to the motherboard and right beneath the wireless card.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    There is a bundle of wires connecting the fan to the motherboard. Disconnect them.
    • There is a bundle of wires connecting the fan to the motherboard. Disconnect them.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using the J00 screw bit in the iFixit tool kit, remove the three screws securing the fan to the case. One screw connected to the bottom case (4cm), one connected to the motherboard (4cm), and one screw connected to the Wireless Card (5cm).
    • Using the J00 screw bit in the iFixit tool kit, remove the three screws securing the fan to the case. One screw connected to the bottom case (4cm), one connected to the motherboard (4cm), and one screw connected to the Wireless Card (5cm).

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully remove the fan from the case using the blue iFixit opening tool.
    • Carefully remove the fan from the case using the blue iFixit opening tool.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The wireless cared is located in the upper left portion of the device case, right above the fan and attached to the motherboard.
    • The wireless cared is located in the upper left portion of the device case, right above the fan and attached to the motherboard.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    There are a bundle of wires connecting the wireless card to the motherboard. Disconnect them.
    • There are a bundle of wires connecting the wireless card to the motherboard. Disconnect them.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully slide the wireless card to the right, and remove it from the device.
    • Carefully slide the wireless card to the right, and remove it from the device.

Linea Traguardo

Un'altra persona ha completato questa guida.

Jessica Browne

Membro da: 18/10/2017

810 Reputazione

6 Guide realizzate

Team

USF Tampa, Team S1-G111, Cagle Fall 2017 Membro di USF Tampa, Team S1-G111, Cagle Fall 2017

USFT-CAGLE-F17S1G111

5 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 40

Tutti i Tempi: 568