Aggiusta la tua roba Comunità Store

Amazon Echo Studio Subwoofer Replacement

Introduzione

This is a guide on how to disassemble an Amazon Echo Studio to be able to replace the subwoofer unit.

Cosa ti serve

  1. Amazon Echo Studio Subwoofer Replacement, Power Supply Board: passo 1, immagine 1 di 3 Amazon Echo Studio Subwoofer Replacement, Power Supply Board: passo 1, immagine 2 di 3 Amazon Echo Studio Subwoofer Replacement, Power Supply Board: passo 1, immagine 3 di 3

    • Flip the device upside down.

    • Pry up the edge of the rubber base panel with a spudger, then pull the rest of it off by hand.

    Modifica

  2. Amazon Echo Studio Subwoofer Replacement: passo 2, immagine 1 di 3 Amazon Echo Studio Subwoofer Replacement: passo 2, immagine 2 di 3 Amazon Echo Studio Subwoofer Replacement: passo 2, immagine 3 di 3

    • Use a T15 Torx screwdriver to remove the nine 3.2 mm screws.

    • Use a Torx T10 screwdriver to remove the six 2.7 mm screws.

    • After removing the screws, gently lift the base off, with care not to damage any of the connected cables.

    Modifica

  3. Amazon Echo Studio Subwoofer Replacement: passo 3, immagine 1 di 3 Amazon Echo Studio Subwoofer Replacement: passo 3, immagine 2 di 3 Amazon Echo Studio Subwoofer Replacement: passo 3, immagine 3 di 3

    • Before fully removing the base, remove the three attached connectors.

    Modifica

  5. Amazon Echo Studio Subwoofer Replacement: passo 4, immagine 1 di 2 Amazon Echo Studio Subwoofer Replacement: passo 4, immagine 2 di 2

    • Now unscrew the the single 10 mm Phillips screw.

    • Remove the power supply board.

    Modifica

  6. Amazon Echo Studio Subwoofer Replacement, Subwoofer: passo 5, immagine 1 di 1

    • Remove the two screws located across from each other on the outside of the plastic ring shown.

    • Remove the plastic outer ring that hugs the inside of the edges of the device.

    • This may require you to use a soft prying tool to separate it from the outer shell.

    Modifica

  7. Amazon Echo Studio Subwoofer Replacement: passo 6, immagine 1 di 3 Amazon Echo Studio Subwoofer Replacement: passo 6, immagine 2 di 3 Amazon Echo Studio Subwoofer Replacement: passo 6, immagine 3 di 3

    • Remove the two 2.7 mm screws with a T10 Torx screwdriver.

    • Once the screws are removed, take the power supply's baseplate out of the unit.

    • You may need to gently pry the subwoofer's air ports from the round slots In the side of the unit.

    Modifica

  8. Amazon Echo Studio Subwoofer Replacement: passo 7, immagine 1 di 2 Amazon Echo Studio Subwoofer Replacement: passo 7, immagine 2 di 2

    • On the silver ring located on the outer edge of the plastic portion of the subwoofer, you will see four 2.7 mm screws. Use a Torx T10 screwdriver to remove them, in order to remove of the subwoofer.

    • Once the four screws have been removed, gently pull the subwoofer out as to not damage the wiring connecting the subwoofer to the main board inside the unit.

    • Follow the wires from the subwoofer to the main board and disconnect the connector attaching them.

    • Your subwoofer is now disconnected and ready to be replaced.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Jaiden Wiles

Membro da: 10/26/22

150 Reputazione

1 Guida realizzata

Distintivi: 4

+ 1 altro distintivo

Team

UMass Dartmouth, Team 2-6, Petersen Fall 2022 Membro di UMass Dartmouth, Team 2-6, Petersen Fall 2022

UMASSD-PETERSEN-F22S2G6

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 18

Tutti i Tempi: 686