Salta al contenuto principale

Ricambi

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove all the selector knob covers by pulling them off.
    • Remove all the selector knob covers by pulling them off.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using needle nose pliers, remove the washers from the four corner selector knobs.
    • Using needle nose pliers, remove the washers from the four corner selector knobs.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.
    • Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully flip the device to the front making sure you secure the face plate and the chassis together. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.
    • Carefully flip the device to the front making sure you secure the face plate and the chassis together.

    • Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.
    • Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys.

    • Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a Phillips #2 screwdriver, remove the thirteen 9.8 mm silver screws holding the mother board to the face plate.
    • Using a Phillips #2 screwdriver, remove the thirteen 9.8 mm silver screws holding the mother board to the face plate.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a Phillips #2 screwdriver, remove the four 9.8mm screws holding in the base of the beat pad.
    • Using a Phillips #2 screwdriver, remove the four 9.8mm screws holding in the base of the beat pad.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slightly lift the mother board near the edge of the beat pads and wiggle the beat pad ribbon connector free. Slightly lift the mother board near the edge of the beat pads and wiggle the beat pad ribbon connector free.
    • Slightly lift the mother board near the edge of the beat pads and wiggle the beat pad ribbon connector free.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the beat pad sensor from the face plate. Remove the beat pad sensor from the face plate.
    • Remove the beat pad sensor from the face plate.

Linea Traguardo

Serbinder Singh

Membro da: 30/01/2013

72 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 20-6, Maness Winter 2013 Membro di Cal Poly, Team 20-6, Maness Winter 2013

CPSU-MANESS-W13S20G6

5 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 22

Tutti i Tempi: 3,748