Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip your laptop over so that the model sticker is facing upward towards the ceiling.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #1 screwdriver to remove the thirteen 6.5mm screws that secure the back cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to gently separate the back cover from the laptop. A snapping sound will be heard as a signal that the clips are being disengaged.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #1 screwdriver to remove two 4 mm screws that secure the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your hand to carefully pull out the wiring harness from its port that is located between the battery and the motherboard.
-
Remove the battery from the case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Tweezers$4.99-
Grasp the CMOS battery with the tweezers and remove it from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a Phillips #1 screwdriver, remove the one 4mm screw that secures the Solid State Drive.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your hand to pull out the Solid State Drive from the motherboard.
-
You will be pulling the solid state drive out to the left, as it will be connected to the port on the motherboard on its right side. This is opposite the direction that the pictures depict it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use Phillips #1 screwdriver to remove the two 4mm screws that are securing the fan.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using Phillips #1 screwdriver remove three 5 mm screws to remove the heatsink.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using your hand, pull out wiring harness to disconnect the fan from the motherboard.
-
Lift the fan out of the case to remove it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Tweezers$4.99-
Use the tweezers to disconnect the wiring harness in the bottom right corner of your laptop.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, flip the white lock tab of the ZIF connector upward.
-
Pull the blue "MB High-Tek" ribbon cable out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, pull the black CQWP connection wire from its port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, flip up the black lock tab of the ZIF connector upward.
-
Pull out the MB purple ribbon cable out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, remove the black drift cable from its port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, pull out the orange GND VCC connection wire.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, flip up the black lock from the connector holding the display cable.
-
Remove the display connection wire from its port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using Phillips #1 screwdriver, remove the 4mm screw that secure the WiFi card.
-
Remove WiFi card from its port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using Philips #1 screwdriver remove the seven 4mm screws that secure the motherboard to the laptop.
-
Remove the motherboard by lifting it out from the back case.
-
Un commento
I was wondering if the CPU is soldered to the motherboard? Is it possible to remove the CPU and replace it with an upgraded CPU?