Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • Remove the thirteen 6.0mm screws on the back panel using your Phillips #1 screwdriver.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 2 : passo 2, immagine 2 di 2
    • Pry the back panel open with the plastic opening tool.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • Remove the two 6.0mm screws securing the battery with your Phillips #1 screwdriver.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Carefully pull out the battery wire connected to the battery port.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 1
    • Slowly lift the battery to remove it from the Chromebook.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Remove the single 3.0mm screw securing the solid state drive using a Phillips #1 screwdriver.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 2 : passo 7, immagine 2 di 2
    • Carefully pull out the solid state drive using two fingers.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 2 : passo 8, immagine 2 di 2
    • Unplug the speaker wire from the motherboard.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • Carefully pull out the speakers from each side of the Chromebook.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 3 : passo 10, immagine 2 di 3 : passo 10, immagine 3 di 3
    • Remove the three 6.0mm screws using the Phillips #1 screwdriver.

    • Remove the two 3.0mm screws using the Phillips #1 screwdriver.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 2 : passo 11, immagine 2 di 2
    • Position the spudger under the switch that connects the ribbon cable to the motherboard.

    • Flick the spudger up to flip the switch up.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 2 : passo 12, immagine 2 di 2
    • Pull the blue tab on the ribbon cable to remove it.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 2 : passo 13, immagine 2 di 2
    • Grab the edges of each piece of circuitry that is included with the SD Card Reader and USB Port.

    • Pull each piece of circuitry out of the Chromebook and remove it from the device.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 2 : passo 14, immagine 2 di 2
    • Position the spudger under the switch.

    • Flick the spudger up to flip the switch up.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 2 : passo 15, immagine 2 di 2
    • Pull on the blue tab of the ribbon cable to remove the ribbon cable.

    • Repeat the previous step and this step with the other ribbon cable that is attached to the SD Card Reader/USB Port.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 2 : passo 16, immagine 2 di 2
    • Using the Phillips #1 screwdriver, remove the four 3.0mm screws.

    • Loosen the six 3.0mm CPU screws using the Phillips #1 screwdriver.

    • The six 3.0mm CPU screws do not come out of the motherboard.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 2 : passo 17, immagine 2 di 2
    • Grab the wire for the two pin connector.

    • Pull the wire to disconnect it from the motherboard.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 2 : passo 18, immagine 2 di 2
    • Place the back of the spudger under the black wire that connects the wireless card to the motherboard.

    • Flick the spudger up to disconnect the cable from the motherboard.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 19, immagine 1 di 2 : passo 19, immagine 2 di 2
    • Place the back of the spudger under the white coaxial antenna wire that connects the wireless card to the motherboard.

    • Flick the spudger up to disconnect the cable from the motherboard.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 20, immagine 1 di 2 : passo 20, immagine 2 di 2
    • Take both wires and unravel them from the CPU fan.

  21. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 21, immagine 1 di 2 : passo 21, immagine 2 di 2
    • Firmly grasp the red, yellow, and white cords with two fingers.

    • Pull the cords to unplug it.

  22. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 22, immagine 1 di 2 : passo 22, immagine 2 di 2
    • Position the spudger under the switch of the big ribbon cable.

    • Flick the spudger up to flip the switch up.

  23. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 23, immagine 1 di 2 : passo 23, immagine 2 di 2
    • Grab the blue tab of the ribbon cable.

    • Pull on the blue tab to disconnect the ribbon cable.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 24, immagine 1 di 3 : passo 24, immagine 2 di 3 : passo 24, immagine 3 di 3
    • Grab the red and black cable near the display cables, this is the cable to the other two pin connector.

    • Pull on the wire to disconnect it from the motherboard.

    • Flip the wire and the connector up to move it out of the way.

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 25, immagine 1 di 2 : passo 25, immagine 2 di 2
    • Position the spudger under the switch for the smaller ribbon cable.

    • Flick the spudger up to flip the smaller switch up.

  26. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 26, immagine 1 di 2 : passo 26, immagine 2 di 2
    • Grab the blue tab on the ribbon cable.

    • Pull on the tab to disconnect the ribbon cable from the motherboard.

  27. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 27, immagine 1 di 2 : passo 27, immagine 2 di 2
    • Position the back of the spudger at the edge of the tape that holds the display cable in.

    • Peel the tape back so it is out of the way.

  28. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 28, immagine 1 di 2 : passo 28, immagine 2 di 2
    • Position the back of the spudger on the display cable.

    • Push the display cable out using the back of the spudger.

  29. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 29, immagine 1 di 2 : passo 29, immagine 2 di 2
    • Lift up the CPU fan to ensure that no wires are tangled. If the black and white wires are tangles please repeat step 5.

    • Lift up the other end of the motherboard to completely remove the motherboard.

Linea Traguardo

Team

Un commento

Plz mujhy mother bother chaiya Chromebook ma ya Merry num 03487834288

Sheryer Shakeel ahmed - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 10

Tutti i Tempi: 332