Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • Place the laptop on a flat surface with the bottom side facing up.

    • Place the tip of a spudger or finger into the hole on the battery release slider.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 2 : passo 2, immagine 2 di 2
    • Use the spudger to move the slider to the right and hold it there.

    • With the slider held, use your other hand to pull the battery back away from the laptop.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • This step will void your device warranty.

    • Use the screwdriver to pierce the warranty sticker.

    • Unscrew and remove the #0 6mm Phillips screw and set it aside.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Slide the back panel towards you. The best spots to place your fingers are on the bumpers.

    • Lift on the front edge to remove the panel.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 2 : passo 5, immagine 2 di 2
    • The hard drive assembly is attached to the laptop by a ribbon cable. Only lift the side of the drive facing you about an inch above the laptop. If you tear the ribbon cable the laptop will need to be serviced by a professional.

    • Use one finger to lift up the hard drive assembly from the bottom left corner.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Hold the hard drive assembly keeping the end closest to you near the laptop. It's ok to tilt the far end of the drive up towards you.

    • Unscrew the two silver #0 3mm Phillips screws on the left and right sides of the hard drive.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Hold the base of the hard drive in your right hand.

    • Use your left hand to pull the hard drive away from its housing. Don't let the housing tug on the ribbon cable.

Linea Traguardo

Altre 21 persone hanno completato questa guida.

Bradley Pavy

Membro da: 09/30/13

1.257 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 13-3, Forte Fall 2013 Membro di Cal Poly, Team 13-3, Forte Fall 2013

CPSU-FORTE-F13S13G3

5 Membri

14 Guide realizzate

8 Commenti

Attempted to upgrade my C710 with the:

PNY XLR8 SATA 120GB 6Gbps 2.5-Inch Solid State Drive SSD9SC120GMDF-RB

Didn't fit.

Unfortunately, one corner of the SSD --near the SATA-connector-- interferes with a screw on the motherboard/chassis. And then the laptop cover cannot be re-attached.

Hope this comment saves someone some grief.

Kevin B - Replica

Not sure I understand.

Pics?

When Ze -

Seems its still not clear what brand/size of SSD that you can upgrade to? 60GB? 120? 480?

When Ze -

Bootable flash drive did not get the C710 working until I reseated the HDD. Never would have known about the hidden screw unless I read this,

-rko

Ray Osborne - Replica

Unit requesting recovery even after carrying out the listed procedure,tried to upgrade to a 128 ssd but won,t, reinstalled hhd after viewing folders on another computer and the unit finally booted again into chrome screen. Would still like to install ssd drive

cabotstephen - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 25

Ultimi 30 Giorni: 100

Tutti i Tempi: 29,629