Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Acer AL1916 EMI Shield Replacement

Introduzione

The EMI shield protects the power supply and circuit board from electromagnetic radiation.

Cosa ti serve

  1. Acer AL1916 EMI Shield Replacement, Stand: passo 1, immagine 1 di 1

    • Lay the monitor on a flat surface so that the back is facing up.

    Traduci

  2. Acer AL1916 EMI Shield Replacement: passo 2, immagine 1 di 2 Acer AL1916 EMI Shield Replacement: passo 2, immagine 2 di 2

    • Grab the hinge cover with both hands on either side of the stand.

    • Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.

    Traduci

  3. Acer AL1916 EMI Shield Replacement: passo 3, immagine 1 di 2 Acer AL1916 EMI Shield Replacement: passo 3, immagine 2 di 2

    • Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor.

    • Support the monitor while removing the screws to prevent the monitor from falling.

    • Lift up to detach the stand.

    Traduci

  5. Acer AL1916 EMI Shield Replacement, Outer Case: passo 4, immagine 1 di 2 Acer AL1916 EMI Shield Replacement, Outer Case: passo 4, immagine 2 di 2

    • Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.

    Traduci

  6. Acer AL1916 EMI Shield Replacement: passo 5, immagine 1 di 3 Acer AL1916 EMI Shield Replacement: passo 5, immagine 2 di 3 Acer AL1916 EMI Shield Replacement: passo 5, immagine 3 di 3

    • Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel.

    • Tilt the plastic opening tool up to separate the back cover from the display bezel.

    • Continue around the perimeter of the monitor until the display bezel comes off.

    • A reasonable amount of force is necessary to detach the back cover from the display bezel.

    Traduci

  7. Acer AL1916 EMI Shield Replacement: passo 6, immagine 1 di 2 Acer AL1916 EMI Shield Replacement: passo 6, immagine 2 di 2

    • Reposition the monitor so that the back is facing up.

    • Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.

    • Lift the back cover up.

    Traduci

  8. Acer AL1916 EMI Shield Replacement, EMI Shield: passo 7, immagine 1 di 2 Acer AL1916 EMI Shield Replacement, EMI Shield: passo 7, immagine 2 di 2

    • Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.

    Traduci

  9. Acer AL1916 EMI Shield Replacement: passo 8, immagine 1 di 2 Acer AL1916 EMI Shield Replacement: passo 8, immagine 2 di 2

    • Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.

    Traduci

  10. Acer AL1916 EMI Shield Replacement: passo 9, immagine 1 di 3 Acer AL1916 EMI Shield Replacement: passo 9, immagine 2 di 3 Acer AL1916 EMI Shield Replacement: passo 9, immagine 3 di 3

    • Grab the metal casing by the sides and slide it down towards the bottom of the monitor.

    • Lift up to remove the metal casing.

    • Beware, metal casing is sharp!

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Taylor Atterbury

Membro da: 10/06/11

717 Reputazione

3 Guide realizzate

Distintivi: 11

+8 altri distintivi

Team

Cal Poly, Team 20-26, Maness Fall 2011 Membro di Cal Poly, Team 20-26, Maness Fall 2011

CPSU-MANESS-F11S20G26

4 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 5

Tutti i Tempi: 1,250