Aggiusta la tua roba Comunità Store

APS Tech 101629 Power Switch Replacement

Introduzione

This repair guide will guide you through the steps to removing and replacing the power switch of your APS Tech 101629 CD-Drive.

First the external casing, and channel switch will need to be removed.

Cosa ti serve

  1. APS Tech 101629 Power Switch Replacement, External Casing: passo 1, immagine 1 di 3 APS Tech 101629 Power Switch Replacement, External Casing: passo 1, immagine 2 di 3 APS Tech 101629 Power Switch Replacement, External Casing: passo 1, immagine 3 di 3

    • Pry all four of the plastic feet off the bottom of the enclosure using the iPod opening tool.

    Modifica

  2. APS Tech 101629 Power Switch Replacement: passo 2, immagine 1 di 2 APS Tech 101629 Power Switch Replacement: passo 2, immagine 2 di 2

    • Unscrew the four screws previously covered by the feet with a Phillips #1 screwdriver.

    Modifica

  3. APS Tech 101629 Power Switch Replacement: passo 3, immagine 1 di 2 APS Tech 101629 Power Switch Replacement: passo 3, immagine 2 di 2

    • Flip the device right side up.

    • Gently slide the casing upwards and off the hard drive.

    Modifica

  5. APS Tech 101629 Power Switch Replacement: passo 4, immagine 1 di 1

    • Flip device upside down again.

    • Gently pry the bottom gray casing away from the device.

    Modifica

  6. APS Tech 101629 Power Switch Replacement: passo 5, immagine 1 di 2 APS Tech 101629 Power Switch Replacement: passo 5, immagine 2 di 2

    • Rotate so the back of the device is facing you.

    • Gently pry the back casing away.

    • When the back casing is removed, the fan will become loose.

    Modifica

  7. APS Tech 101629 Power Switch Replacement, Channel Switch: passo 6, immagine 1 di 2 APS Tech 101629 Power Switch Replacement, Channel Switch: passo 6, immagine 2 di 2

    • Find the conjoined ID cable wires that are colored black, orange, and yellow.

    • Lift white portion of cable wires to disconnect it.

    Modifica

  8. APS Tech 101629 Power Switch Replacement: passo 7, immagine 1 di 3 APS Tech 101629 Power Switch Replacement: passo 7, immagine 2 di 3 APS Tech 101629 Power Switch Replacement: passo 7, immagine 3 di 3

    • At this point, the fan is loose and can be easily moved but not disconnected.

    • Using the spudger, depress the pressure holders at all four corners of the fan.

    • Take out the fan and its cords, by pulling it outward from its cavity within the device.

    Modifica

  9. APS Tech 101629 Power Switch Replacement, Power Switch: passo 8, immagine 1 di 2 APS Tech 101629 Power Switch Replacement, Power Switch: passo 8, immagine 2 di 2

    • Depress 2 pressure holds on each side of the power switch.

    • Press out the back of the device.

    Modifica

  10. APS Tech 101629 Power Switch Replacement: passo 9, immagine 1 di 2 APS Tech 101629 Power Switch Replacement: passo 9, immagine 2 di 2

    • Remove all four 4 connections from the power switch.

    • Remember that the straight connections are on the far side, while the L-shaped connections are on the near side, and that both yellow connections are on top. This is helpful for reassembly.

    • These are very hard to get off, use patience and wiggling.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 6 altri collaboratori

Alexis Weckel

Membro da: 04/11/11

140 Reputazione

3 Guide realizzate

Distintivi: 6

+3 altri distintivi

Team

Cal Poly, Team 24-60, Amido Spring 2011 Membro di Cal Poly, Team 24-60, Amido Spring 2011

CPSU-AMIDO-S11S24G60

5 Membri

12 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 557