Salta al contenuto principale

Introduzione

This guide walks you through how to replace the lens on a 360fly 4K camera.

  1. Flip the camera upside down and peel off the two plastic screw covers with the metal spudger to reveal the screws.
    • Flip the camera upside down and peel off the two plastic screw covers with the metal spudger to reveal the screws.

  2. Remove the two 5 mm screws from the bottom of the camera with a T4 screwdriver.
    • Remove the two 5 mm screws from the bottom of the camera with a T4 screwdriver.

  3. Gently pry the plastic ring from around the charging plate with the metal spudger. Remove the outside shell by pressing against the center of the charging plate and pulling the bottom shell away from the top shell.
    • Gently pry the plastic ring from around the charging plate with the metal spudger.

    • Remove the outside shell by pressing against the center of the charging plate and pulling the bottom shell away from the top shell.

  4. Remove the five 2 mm screws using a T4 screwdriver.
    • Remove the five 2 mm screws using a T4 screwdriver.

    • Pull off the charging plate assembly.

  5. Gently pry the plug off the port on the circuit board with a plastic opening tool. Remove the four 2 mm screws using a T4 screwdriver.
    • Gently pry the plug off the port on the circuit board with a plastic opening tool.

    • Remove the four 2 mm screws using a T4 screwdriver.

    • Remove the circuit board from the device.

  6. Remove the five 4 mm screws around the battery assembly with a T4 screwdriver. Lift the battery assembly and gently pry the plug out of its port on the board below with a plastic opening tool. Press the battery from the back  of the battery assembly to remove it with a plastic opening tool until the glue releases the battery.
    • Remove the five 4 mm screws around the battery assembly with a T4 screwdriver.

    • Lift the battery assembly and gently pry the plug out of its port on the board below with a plastic opening tool.

    • Press the battery from the back of the battery assembly to remove it with a plastic opening tool until the glue releases the battery.

    • Potential for device damage: Do not puncture or bend the battery. Use a small amount of heat to assist in softening the adhesive if necessary.

  7. Gently pry the plug from  the motherboard and remove the motherboard from the assembly.
    • Gently pry the plug from the motherboard and remove the motherboard from the assembly.

  8. Remove the  three 3 mm screws from the circuit assembly with a T4 screwdriver.
    • Remove the three 3 mm screws from the circuit assembly with a T4 screwdriver.

  9. Gently pry out the plug from the circuit assembly.
    • Gently pry out the plug from the circuit assembly.

  10. Press and release the SD card to remove it from the circuit assembly.
    • Press and release the SD card to remove it from the circuit assembly.

  11. Unscrew the five 3mm screws with a T4 screwdriver.
    • Unscrew the five 3mm screws with a T4 screwdriver.

  12. Gently push against the  lens module to remove it from the 360fly 4K assembly.
    • Gently push against the lens module to remove it from the 360fly 4K assembly.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Jacob Herron

Membro da: 08/11/2017

421 Reputazione

3 Guide realizzate

Team

IUPUI, Team S5-G3, Baechle Fall 2017 Membro di IUPUI, Team S5-G3, Baechle Fall 2017

IUPUI-BAECHLE-F17S5G3

3 Membri

3 Guide realizzate

Hi. Where to get a replacement lens as I am in need for this repair, but 360fly offer a full service for $150 and do not sell spare lenses. Thx

anguel nakov - Replica

There is no info where to buy the replacement lens.

gelo3000 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 12

Tutti i Tempi: 1,121