Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Put the car in park (automatic) or neutral (manual).
-
Apply the parking brake.
-
Place chocks behind the rear wheels.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a 19 mm lug wrench to loosen each lug nut a half turn.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a hydraulic jack on the car's frame to jack the car.
-
A small notch shows where to place the jack.
-
It is only necessary to jack the car until the wheel no longer touches the ground.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place a jack stand on the frame and remove the jack.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a lug wrench to completely remove the four lug nuts.
-
Remove the wheel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The brake fluid reservoir is located towards the back of the engine compartment.
-
Unscrew the cap and remove it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a turkey baster to remove 2-3 ounces of brake fluid from the reservoir.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a flat head screwdriver or brake spoon to remove the outer pad retaining clip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a flat head screwdriver to remove the black plastic guide bolt dust caps.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a 7 mm Allen wrench to remove the two caliper guide bolts.
-
On the driver's side, turn towards the rear of the car. On the passenger side, turn towards the front
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the clip that holds the brake line to the strut with a pair of vise grips.
-
Pull the brake line towards you and out of the bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the caliper off of the rotor.
-
Place the caliper on top of a box or bucket so the brake line doesn't stretch or kink.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the outer brake pad from the mounting bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the inner brake pad from the caliper.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a flat head screwdriver to push the bushing through its hole in the caliper.
-
Remove the bushing from the caliper.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Clean the rotor, caliper, and all other hardware with an aerosol brake cleaner.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Coat the steel backing plates of the new brake pads with an anti-squeal coating.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the new outer pad on the mounting bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the new bushing from the inside of the caliper.
-
Use a flat head screwdriver to help feed the bushing through its hole.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Compress the caliper piston with a C-clamp.
-
Install the new inner pad by pressing it into the caliper and making sure the clips are secure.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grease the two guide bolts and reinstall them.
-
Reinstall the guide bolt dust caps.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the brake line back in the bracket on the strut.
-
Secure the brake line with the retaining clip. Use the blunt end of a wrench to knock it completely into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reinstall the retainer clip by first inserting the ends into the two holes in the caliper, then use pliers to stretch the ends onto the mounting bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Put the wheels back on the car and hand tighten the lug nuts.
-
Lower the car and completely tighten the lug nuts
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the cap back on the brake fluid reservoir.
-
Turn the key to the "on" position. Press the brake pedal a few times. It should go to the floor once, and then become firm.
-
Fill the brake fluid reservoir with new fluid, if needed.
-
Replace the brake fluid reservoir cap, close the hood, and lower the car.
-
Annulla: non ho completato questa guida.
Altre 24 persone hanno completato questa guida.
8 Commenti
Excellent guide --- many thanks ! Also applicable with virtually no modifications to my 2012 Ford Ikon, except that on my car the guide pins needed a size 45 Torx bit to unscrew. I had to replace the rotors as well, and discovered Ford had used threadlocking compound on the mounting bolts for the bracket, making them the devil to remove without pneumatic wrench. Threadlocking compound should be outlawed !!
GEB
Awesome guide. Very helpful. No trouble at all.
Top effort… just saved myself £25!