Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. , Apertura cofano: passo 1, immagine 1 di 2 , Apertura cofano: passo 1, immagine 2 di 2
    • Trova la leva del cofano accanto alla porta del lato del conducente, vicino al poggiapiedi sinistro.

    • Tira la leva verso di te per sbloccare il cofano.

  2. : passo 2, immagine 1 di 2 : passo 2, immagine 2 di 2
    • Vai davanti al cofano dell'auto.

    • Infila la mano sotto il cofano, sopra lo stemma della Honda. Trova e tira l'aletta di bloccaggio sotto il cofano per liberarlo.

    • Una volta liberata l'aletta, apri il cofano.

  3. : passo 3, immagine 1 di 2 : passo 3, immagine 2 di 2
    • Usa una mano per tenere aperto il cofano. Trova l'asta di supporto del cofano e liberala dal gancio.

    • Posiziona la punta del supporto del cofano nel foro situato nell'angolo superiore sinistro del cofano.

    • Ora puoi far riposare il cofano sul supporto.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 3 : passo 4, immagine 2 di 3 : passo 4, immagine 3 di 3
    • Be sure your engine is turned off.

    • Identify the engine's air duct hose.

    • The emission hose is located on the top.

    • Remove the emission hose by gently wiggling it out of place.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 2 : passo 5, immagine 2 di 2
    • Remove the smog hose by squeezing the tubing and pulling it off.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 1
    • Using a Phillips screwdriver, loosen air duct clamp screws.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 2 : passo 7, immagine 2 di 2
    • Once the screws are loose, completely remove the air duct hose by gently wiggling it off the engine and the air filter housing.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 3 : passo 8, immagine 2 di 3 : passo 8, immagine 3 di 3
    • Remove the air filter housing cap.

    • Using a long Phillips screwdriver or a long 5/16 Hex driver, remove the four screws holding down the air filter housing cap.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 1
    • Lift the engine air filter housing cap and place it aside.

    • Do not turn the housing cap upside down. Screws left in holes of housing cap might fall out.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • Lift the dirty filter out of the housing.

    • Vacuum any dirt or debris out of the air filter box.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Replace the old filter with the new filter.

    • Ensure that it seats properly in the lip of the air cleaner box.

    • Screw down the air filter housing cap. Connect air dust, emission, and smog hoses.

Linea Traguardo

Altre 21 persone hanno completato questa guida.

Team

Cal Poly, Team 24-27, Regan Fall 2012 Membro di Cal Poly, Team 24-27, Regan Fall 2012

CPSU-REGAN-F12S24G27

4 Membri

21 Guide realizzate

4 Commenti

Okay, I have an Acura TSX (Euro Accord) with the K24A engine, which is similar, and can assure you that you do not need to remove all these connections and hoses just to open the engine air cleaner . The AIR CLEANER COVER (where the filter lives) can be gently lifted up sufficiently to open up, remove the AIR CLEANER ELEMENT ASSY (filter), vacuum out debris from AIR CLEANER CASE, and install a new filter.

David Spalding - Replica

For a 2006 Accord L4, you definitely need to remove the air intake hose as the front lip of the air cleaner box will not clear the inner fender by about 1/4" on the left side. Never had problems with any other newer or older hondas and toyotas with having to remove the air intake hose to open the air cleaner box. This is why I came here for advice. thanks OP.

Michael Lee - Replica

emission hose where can I find it at ? Mine broke

Moda Zuniga - Replica

You use metric tools on Hondas because they are a foreign car. Use an 8mm socket with an extension to remove the screws from the air filter cover.

Mary Petersonma - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 26

Ultimi 30 Giorni: 138

Tutti i Tempi: 33,159