1978 Datsun 280Z Turn Signal Flasher Replacement

Lola Yates e 2 altri collaboratori

Ultimo aggiornamento il June 20, 2024

30 minuti

Moderato

Guida Studente in Evidenza

Introduzione

Vai al passo 1

A fully functional set of turn signals is not only required by law, but vital for good communication and overall road safety. If one or more of your turn signals have stopped working or are not functioning properly, you may have a bad flasher unit.

In this tutorial, we will demonstrate how to replace the flasher unit on a 1978 Datsun 280Z.

Warning: This procedure includes tasks that can cause severe damage to your equipment and health if you fail to follow the precautions outlined within this procedure.

Cosa ti serve

iFixit guadagna commissioni quando acquisti tramite questi link.

Passo 1 Turn Signal Flasher

1978 Datsun 280Z Turn Signal Flasher Replacement, Turn Signal Flasher: passo 1, immagine 1 di 3

1978 Datsun 280Z Turn Signal Flasher Replacement, Turn Signal Flasher: passo 1, immagine 2 di 3

1978 Datsun 280Z Turn Signal Flasher Replacement, Turn Signal Flasher: passo 1, immagine 3 di 3

Locate the hood latch on the bottom left side of the steering wheel.
Pull the latch to release the hood.

Modifica

Passo 2

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 2, immagine 3 di 3

Unclip and lift the hood.

Modifica

Passo 3

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 3, immagine 3 di 3

Lift the inspection cover on the left side to uncover the battery.

Modifica

Passo 4

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 4, immagine 3 di 3

Attach a 13mm socket to a ratchet extension then attach the extension to a drive ratchet.
Loosen the 13mm bolt from the negative terminal of the battery.
You do not need to remove the nut from the terminal bolt completely. The terminal should slide off the post once the nut is loose.
Be sure to keep your ratchet or any other metal items from touching both the positive and negative terminals while performing this task. Connecting metal to both terminals creates a new path of electricity and could cause serious chemical, electrical, and flammable damage to your equipment and/or health.

Modifica

Passo 5

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 5, immagine 3 di 3

Remove the negative battery cable from the post and set it far enough aside so that it cannot come in contact with the negative battery post while you are working.
If the negative terminal comes in contact with the negative battery post while you are performing electrical work, the vehicle will become energized and you risk damaging your equipment and shocking yourself.
Wait 10 minutes for electricity to bleed out of the system to ensure safety in the proceeding steps.

Modifica

Passo 6

The flasher is located under the dash on the right side of the steering wheel column.

Modifica

Passo 7

Disconnect the cable from the flasher.
It is a good idea to inspect the wires for corrosion, heat marks, open wires and other defects. Any of these defects could be a reason your flasher became faulty in the first place and possibly lead to another faulty flasher in the future if not addressed.

Modifica

Passo 8

Attach a 10mm socket to an extension then attach the extension to a drive ratchet.
Unbolt and dismount the flasher.

Modifica

Passo 9

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 9, immagine 3 di 3

The aftermarket flasher replacement doesn’t come with a fixed mounting L-bracket, so it’s necessary to create a safe and functional alternative.

Modifica

Passo 10

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 10, immagine 3 di 3

Place new the flasher parallel to the new L-bracket.
Slide in the L-bracket in between the new flasher and the hose clamp.

Modifica

Passo 11

Tie the L-bracket to the flasher with the hose clamp once they are aligned.
Do not over tighten, as there are fragile plastic parts inside the new flasher that can break.

Modifica

Passo 12

Bolt in the new flasher using the same 10mm socket and drive ratchet assembly you created from step 8.

Modifica

Passo 13

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 13, immagine 3 di 3

Connect the cable.

Modifica

Passo 14

1978 Datsun 280Z Turn Signal Flasher Replacement: passo 14, immagine 3 di 3

Reconnect the negative battery terminal by reversing the order of tasks outlined in step 5.
Be sure to fasten the cable to the post tight enough so that it can not slip off the terminal post under any circumstances.
Power up your vehicle and test your turn signals.