DMC-TZ5.pdf
LUMIX
Panasonic
ORDER NO.DSC0803021CE B26
Digital Camera
Model No.DMC-TZ5P DMC-TZ5PC DMC-TZ5PL DMC-TZ5PR DMC-TZ5EB DMC-TZ5EE DMC-TZ5EF DMC-TZ5EG DMC-TZ5E DMC-TZ5SG DMC-TZ15GC DMC-TZ15GD DMC-TZ15GK DMC-TZ15GN DMC-TZ15GT DMC-TZ15GJ
VOL.1
Colours (S)....................Silver Type (except PR/GD) (K)....................Black Type (A)....................Blue Type (only DMC-TZ5P/PC/PL/PR/ EE/EG/E) (TA)....................Dark Brown Type (only DMC-TZ5EF/ EG/E) (T)....................Brown Type (only DMC-TZ5SG, DMCTZ15GC/GK/GJ)
© 2008 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product:. Products powered by electricity should be serviced or repaired only by experienced professional technicians: attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious injury or death. Any
TABLE OF CONTENTS
| PAGE | |
|---|---|
| 1 Safety Precaution --- | 4 |
| 1.1. General Guidelines--- | 4 |
| 1.2. Leakage Current Cold Check--- | 4 |
| 1.3. Leakage Current Hot Check (See Figure 1) | --- 4 |
| 1.4. How to Discharge the Capacitor on Flash PCB--- | 5 |
| 2 Warning | --- 6 |
| 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices --- | 6 |
| 2.2. How to Recycle the Lithium Ion Battery (U.S. | |
| Only) --- EB/GC/SG)--- | 6 7 |
| 2.3. Caution for AC Cord (For Battery --- | |
| 2.4. How to Replace the Lithium | 8 |
| 3 Service Navigation | --- 9 |
| 3.1. Introduction--- | 9 |
| 3.2. General Description About Lead Free Solder (PbF)--- | 9 |
| 3.3. Important Notice 1:(Other than U.S.A. and Canadian Market) --- 3.4. How to Define the Model Suffix (NTSC or PAL | 9 |
| 4 Specifications | --- 13 |
| 5 Location of Controls and Components | --- 15 |
| 6 Service Mode --- | 17 |
| 6.1. Error Code Memory Function---17 | |
| 7 Service Fixture & Tools --- | 20 |
| 7.1. Service Fixture and Tools---20 | |
| 7.2. When Replacing the Main PCB---20 | |
| 7.3. Service Position---20 | |
| 8 Disassembly and Assembly Instructions | --- 22 |
| 8.1. Disassembly Flow Chart---22 | |
| 8.2. PCB Location---22 | |
| 8.3. Disassembly Procedure---23 | |
| 8.4. Disassembly Procedure for the Lens---28 | |
| 8.5. Assembly Procedure for Lens---31 | |
| 8.6. Removal of the CCD Unit---35 | |
| 8.7. Removal of the Zoom Motor Unit---36 | |
| 8.8. Removal of the Focus Motor Unit | ---36 |
| 8.9. The Applyment of grease Method---37 | |
| 9 Measurements and Adjustments --- | 38 |
| 9.1. Matrix Chart for Replaced Part and Necessary Adjustment ---38 | |
| Maintenace --- | 39 |
| 10.1. Cleaning Lens, Viewfinder and LCD Panel | ---39 |
Table Caption: This table is a table of contents for a service manual, outlining safety precautions, warnings, service navigation, specifications, component locations, service modes, tools, disassembly and assembly procedures, and maintenance instructions. It details the content and corresponding page numbers for each section.
PAGE
1 Safety Precautions
1.1. General Guidelines
- IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-RADIATION, shock fire, or other hazards. Do not modify the original design without permission of manufacturer.
- An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
- When servicing, observe the original lead dress. It a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
- After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
- After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2. Leakage Current Cold Check
- Unplug the AC cord and connect a jumper between the two prongs on the plug.
- Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1M Ω and 5.2M Ω . When the exposed metal does not have a return path to the chassis, the reading must be infinity.
1.3. Leakage Current Hot Check (See Figure 1)
- Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
- Connect a 1.5k Ω , 10 W resistor, in parallel with a 0.15 μ F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1.
- Use an AC voltmeter, with 1 k Ω /V or more sensitivity, to measure the potential across the resistor.
- Check each exposed metallic part, and measure the voltage at each point.
- Reverse the AC plug in the AC outlet and repeat each of the above measurements.
- The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
Hot-Check Circuit
1.4. How to Discharge the Capacitor on Flash PCB
CAUTION:
- Be sure to
