Briggs-&-Stratton-Workshop-Man.pdf

TABLE OF CONTENTS

I

Table Caption: This table is a table of contents for a technical manual, outlining various sections related to engine components and systems, from general information to specific parts like pistons and bearings, and including sections on ignition, oil systems, and tools.

Fraction

1/64

1/32

3/64

1/16

5/64

3/32

7/64

1/8

9/64

5/32

11/64

3/16

13/64

7/32

15/64

1/4

17/64

9/32

19/64

5/16

21/64

11/32

23/64

3/8

25/64

13/32

27/64

7/16

29/64

15/32

31/64

1/2

Decimal

0.0156

0.0312

0.0469

0.0625

0.0781

0.0938

0.1094

0.1250

0.1406

0.1562

0.1719

0.1875

0.2031

0.2188

0.2344

0.2500

0.2656

0.2812

0.2969

0.3125

0.3281

0.3438

0.3594

0.3750

0.3906

0.4062

0.4219

0.4375

0.4531

0.4688

0.4844

0.5000

English to Metric Conversion Table

mm

0.3969

0.7938

1.1906

1.5875

1.9844

2.3812

2.7781

3.1750

3.5719

3.9688

4.3656

4.7625

5.1594

5.5562

5.9531

6.3500

6.7469

7.1438

7.5406

7.9375

8.3344

8.7312

9.1281

9.5250

9.9219

10.3188

10.7156

11.1125

11.5094

11.9062

12.3031

12.7000

Table Caption: This table lists fractions with denominators of 32 and 64, their decimal equivalents, and corresponding millimeter measurements, ordered from smallest to largest. It appears to be a conversion chart for fractional inch measurements to millimeters.

Table Caption: This table lists drill bit sizes, presented in both fractional and numerical formats, alongside their corresponding decimal equivalents in inches. It provides a comprehensive reference for selecting the appropriate drill bit based on its diameter.

THE OPERATING & MAINTENANCE INSTRUCTIONS CONTAIN SAFETY INFORMATION TO

• Make you aware of hazards associated with engines
• Inform you of the risk of injury associated with those hazards, and
• Tell you how to avoid or reduce the risk of injury.

The safety alert symbol ( ) is used to identify safety information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury.

CAUTION , when used without the alert symbol, indicates a situation that could result in damage to the engine.

SAFETY

Gaseous fuels are extremely flammable and readily form explosive air-vapor mixtures at ambient temperatures.

IF YOU SMELL GAS:

• DO NOT start the engine.
• DO NOT actuate any electrical switches.
• DO NOT use the phone in the vicinity.
• Evacuate the area.
• Contact the gas supplier or fire department.

REMEMBER:

• Vapor is heavier than air and may travel to remote locations.
• Keep all flames, sparks, pilot lights, and other ignition sources away from the area where the engine is operated or repaired.
• DO NOT smoke when operating or repairing the engine.
• DO NOT store gasoline or other flammable vapors or liquids in the vicinity of the engine.
• BEFORE doing any service work to the engine, shut off the gas supply.
• After initial installation or servicing, check for gas leaks. DO NOT use an open flame. Apply very soapy water or leak test solution with a brush and look for bubbles.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic amputation, or laceration.

BEFORE PERFORMING ADJUSTMENTS OR REPAIRS

• Disconnect spark plug wire